Results 191 to 200 of about 2,467 (241)

Study on Microstructure and Thermal Cracking Sensitivity of Deposited Ti6Al4V/Inconel 718 Composites Made by Two-Wire Arc Additive Manufacturing by Current. [PDF]

Materials (Basel)
Xia P, Ye X, Zhang G.
europepmc   +1 more source

Engineering Strategies to Suppress Thermal Runaway Propagation in Lithium‐Ion Battery: Mechanisms, Metrics, Materials, and Evaluation Methods

Advanced Science, Volume 13, Issue 44, 7 August 2026.
Thermal runaway propagation can transform a single‐cell failure into a system‐level hazard in lithium‐ion battery packs. This review clarifies how heat transfer, gas venting, combustion, and configuration govern cell‐to‐cell failure, and links measurable metrics, pathway‐oriented suppression materials, and experimental/modeling tools to guide safer ...
Jinrong Su, Anna DiFelice, Jayani Mawela, Jianing Gan, Shuai Che, Wonhee Cho, Hanghang Yan, Yaohong Xiao, Xinxin Yao, Xiangwei Guo, Rui Wang, Dingchuan Xue, Hanlong Liu, Solomon Adera, Zhan Chen, Lei Chen   +15 more
wiley   +1 more source

Effect of induction heat treatment on microstructure, mechanical and corrosion properties of stainless steel 308 L fabricated using wire arc additive manufacturing. [PDF]

Sci Rep
Sun Y, Li X, Xu L, Shen H, Liu Y.
europepmc   +1 more source

Grid Optimization of Tunnel Oxide Passivated Back Contact Silicon Solar Cells

Progress in Photovoltaics: Research and Applications, Volume 34, Issue 8, Page 1037-1051, August 2026.
The grid pattern design of tunnel oxide passivated back contact silicon solar cells were optimized via device simulation and the estimated cell efficiency was correlated to the required Ag paste consumption. The absolute efficiency gain of zero‐busbar design over pad‐based contact design is more than 0.1%, with increasing advantage when the Ag paste ...
Pei‐Chieh Hsiao, Kangping Zhang, Zibo Zhou, Jessica Yajie Jiang, Lingzhi Li, Jianfang Dai, Yimin Ji, Jiadong Li, Dengyuan Song, Renate Egan, Martin Green   +10 more
wiley   +1 more source

Corrosion Performance of Wire Arc Additive Manufacturing of Stainless Steel: A Brief Critical Assessment. [PDF]

3D Print Addit Manuf
Omiyale BO, Ogedengbe II, Olugbade TO, Farayibi PK.   +3 more
europepmc   +1 more source

D–A–π–A Fused Pentacyclic Organic Dyes as Sensitizers for Dye‐Sensitized Solar Cells Operating under Low‐Light Conditions

ChemistrySelect, Volume 11, Issue 30, 10 August 2026.
The highly conjugated [1]benzothieno[3,2‐b]thieno[2,3‐f][1]benzothiophene (TBTBT) moiety was introduced for the first time as a mild donor group in the structure of three D‐A‐π‐A organic dyes. The compounds were prepared through appropriate multistep synthetic sequences and fully characterized. Dye‐sensitized solar cells fabricated with the new dyes as
Francesco D'Amico, Matteo Bartolini, Carmen Coppola, Adalgisa Sinicropi, Alessandro Mordini, Gianna Reginato, Massimo Calamante, Daniele Franchi, Lorenzo Zani, Alessio Dessì   +9 more
wiley   +1 more source

Wire Arc Additive Manufacturing of NiTi 4D Structures: Influence of Interlayer Delay. [PDF]

3D Print Addit Manuf
Singh S, Palani IA, Paul CP, Funk A, Konda Gokuldoss P.   +4 more
europepmc   +1 more source

Increasing the Reuse Potential of High‐Strength Steels by Extending the Fatigue Life through Surface Treatments

steel research international, Volume 97, Issue 8, Page 4326-4336, August 2026.
Surface reconditioning through mechanical and electrochemical polishing is shown to extend the fatigue life of predamaged 42CrMo4 steel by over 12 times. By removing ≈100 μm of surface material, surface‐driven fatigue damage is mitigated. This study introduces a reuse potential metric to evaluate fatigue recovery and support sustainable steel reuse. To
Ayush Shrivastava, Oguz Gulbay, Srinivasa Raghavan Raghuraman, Marion Kreins, Fabian Weber, Peter Starke, Alexander Gramlich, Ulrich Krupp   +7 more
wiley   +1 more source

A Net Shape Profile Extraction Approach for Exploring the Forming Appearance of Inclined Thick-Walled Structures by Wire Arc Additive Manufacturing. [PDF]

Micromachines (Basel)
Zheng Y, Li Y, Zhou Y, Wang X, Zhang G.
europepmc   +1 more source

Distortion Analysis Method for Wire Arc Additive Manufacturing Component Using Thermomechanical Computation with Enhanced Separation and Deposition Algorithm. [PDF]

3D Print Addit Manuf
Prajadhiana KP, Taufek T, Wan Abdul Rahaman WE, Manurung YHP, Adenan MS, Mat MF, Mohamad Fuzi MFAB, Mohammed Nasir MAB, Mohamed MA, Jamaludin MF, Triyono.   +10 more
europepmc   +1 more source