Results 21 to 30 of about 1,735 (179)
Parameters Optimization of Electrical Discharge Machining Process Using Swarm Intelligence: A Review
Metals, 2023 Electrical discharge machining (EDM) can use soft tool electrodes to process hard workpieces to achieve “soft against hard”, because it directly uses electrical energy and thermal energy to remove metal materials.
Yanyan Chen +5 more
doaj +1 more source
Effect of Machining Parameters on Surface Roughness and Metal Removal Rate for AISI 310 L Stainless Steel in WEDM [PDF]
Engineering and Technology Journal, 2022 Wire electrical discharge machining (WEDM) is a non-traditional machining process that is widely used in the machining of conductive materials. This paper presents the investigation on surface roughness and metal removal rate of stainless steel using the
Muayad Ali, Abbas Ibrahim
doaj +1 more source
Effect of the Micro Wire-EDM Process Parameters on the Recast Layer in the Molybdenum Micromachining [PDF]
International Journal of Advanced Design and Manufacturing Technology, 2017 The Micro wire electrical discharge machining (Micro wire-EDM) process is a modern machining process with various applications in manufacturing micro-parts. The recast layer remaining on the machined surfaces is an inevitable complication of this process.
Mohammad Tahmasebipour +3 more
doaj
Simetris: Jurnal Teknik Mesin, Elektro dan Ilmu Komputer, 2018 Proses wire-electrical discharge machining (wire-EDM) sering digunakan dalam industri manufaktur. Parameter pemesinan yang terdapat dalam wire-EDM di antaranya, arc on time, on time, servo voltage dan wire feed.
Pathya Rupajati +2 more
doaj +1 more source
Micromachines, 2020 Micro-electrical discharge machining (micro-EDM) is a good candidate for processing micro-hole arrays, which are critical features of micro-electro-mechanical systems (MEMS), diesel injector nozzles, inkjet printheads and turbine blades, etc.
Zhixiang Zou +5 more
doaj +1 more source
A brief review on the status of machining technology of fir-tree slots on aero-engine turbine disk
Advances in Mechanical Engineering, 2022 The machining precision and its consistency of turbine disk fir-tree slots have a direct influence on the performance of aero-engine rotor components. However, the structural dimensions of fir-tree slot are small, and the cutting performance of materials
Yu Jianhua +4 more
doaj +1 more source
Journal of Applied Science & Process Engineering, 2023 Despite being contemporary, the wire electrical discharge machining (EDM) industry is burdened with complicated and challenging problems. However, the double optimisation method involving Taguchi analyses and genetic algorithms is a powerful tool to ...
Meshach Chukwuebuka Ikedue +5 more
doaj +1 more source
Optimization Performance Parameters of OHNS Die Steel using Dimensional Analysis Intergrated with Desirability Function [PDF]
International Journal of Industrial Engineering and Production Research, 2019 In the Wire EDM of oil hardening die steel materials is a complicated machining process. Hence to find out the best set of process parameters is an important step in wire EDM process.
Mangesh Phate +2 more
doaj +1 more source
Ignition Delay Time Modeling in Wire-EDM
Journal of Manufacturing and Materials Processing, 2023 This study presents a comprehensive investigation and modeling of the ignition delay time (td) in wire-EDM (WEDM). The research focuses on the influence of gap distance, discharge energy, and piece height on the stochastic distributions of td, providing ...
Paulo Matheus Borges Esteves +3 more
doaj +1 more source
A review on Wire-EDM of bio titanium
Reports in Mechanical Engineering, 2023 Nonconventional machining technologies have been found viable to manufacture various products from a wide range of engineering materials. Wire electric discharge machining (WEDM), also known as Wire-EDM, is one of the important thermal type nonconventional machining technologies.
Sujeet Kumar Chaubey, Kapil Gupta
openaire +1 more source