Results 11 to 20 of about 2,255 (260)
An overview of major research areas in Wire cut EDM on different materials [PDF]
INCAS Bulletin, 2020 WEDM (Wire electrical discharge machining) is a precision machining method for cutting electrically conductive materials. It is an unconventional machining process that produces precision parts that match the dimensional tolerances of our designs within ...
M. CHAITANYA REDDY, K. VENKATA RAO
doaj +1 more source
Experimental Investigation of Wire EDM Process Parameters on Heat Affected Zone [PDF]
Engineering and Technology Journal, 2018 It is vital to study the impact of heat since it has an unwanted phenomenon on the operating life of parts produced, which is in turn effect the cost of production.
V.N. Najm
doaj +1 more source
Journal of Materials Research and Technology, 2020 Machinability comparisons have been made between superalloys such as Incoloy 825, Inconel 603 XL, Monel K400, and Inconel 600 using wire cut electrical discharge machining based on straightness, surface roughness and perpendicularity.
K. Manikandan +3 more
doaj +1 more source
Micro Pin Fabrication of Tungsten Carbide Using Polycrystalline Diamond [PDF]
한국정밀공학회지, 2020 Micro tool fabrication is crucial in micro machining. Wire electro-discharge grinding (WEDG) is one of the popular methods applied to fabricate micro tools used for micro electrical discharge machining (EDM), electrochemical machining (ECM), and ...
Joo A Park, Ui Seok Lee, Bo Hyun Kim
doaj +1 more source
Performance and Surface Integrity of Wire Electrical Discharge Machining of Thin Ti6al4v Plate Using Coated and Uncoated Wires [PDF]
Materials Research, 2019 Wire Electrical Discharge Machining (WEDM) is one of the most important production technologies to manufacture very accurate small components and tools on any electrical conductive material. Titanium and its alloys have been widely used in automobile and
Fred Lacerda Amorim +3 more
doaj +1 more source
REQUIREMENTS AND SOLUTIONS FOR A DEVICE FOR WIRE ELECTRICAL DISCHARGE MACHINING
Nonconventional Technologies Review, 2021 Rectilinear kerfs in workpieces made of hard electroconductive materials can be made by wire erosion electrical discharge machining. However, since machine tools intended for such machining are rarer and more expensive, the problem of using devices for ...
Laurentiu Slatineanu +6 more
doaj
Advances in Mechanical Engineering, 2017 The mechanism of surface topography formation of Inconel 718 in low-speed wire electrical discharge machining was studied, and its on-line prediction based on acoustic emission detection technology is carried out.
Yan Wang, Duxing He, Lin Yang, Wei Xiong
doaj +1 more source
Advances in Materials Science and Engineering, 2022 In this work, wire cut electrical discharge machining (WEDM) is used for the material removing processes; it is utilized for machining conductive parts where it is required to produce complicated shapes, new profiles, new geometry, new product ...
Sathishkumar Seshaiah +7 more
doaj +1 more source
Optimization of Machining Parameters for Corner Accuracy Improvement for WEDM Processing
Applied Sciences, 2022 Corner accuracy occurring in wire electrical discharge machining (WEDM) is influenced by machining parameters such as wire vibration, wire lag, and excessive discharge, etc. This study proposed an optimization method which can improve the corner accuracy
Shih-Ming Wang +3 more
doaj +1 more source
Effect of Machining Parameters on Surface Roughness and Metal Removal Rate for AISI 310 L Stainless Steel in WEDM [PDF]
Engineering and Technology Journal, 2022 Wire electrical discharge machining (WEDM) is a non-traditional machining process that is widely used in the machining of conductive materials. This paper presents the investigation on surface roughness and metal removal rate of stainless steel using the
Muayad Ali, Abbas Ibrahim
doaj +1 more source