Results 31 to 40 of about 6,389,749 (288)

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

Fundamental study on fine wire EDM characteristics using γ-phase brass coated steel wire

Nihon Kikai Gakkai ronbunshu, 2020
Demand for high precision machining of complicated shapes has recently increased with the miniaturization of mechanical and electronic products. Therefore, further development of fine wire electrical discharge machining (EDM) technology using a thin wire
Masato MIYOSHI, Shixian LIU, Akira OKADA, Akihito HOSHIMA, Masatoshi KUITA   +4 more
doaj   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Field Induced Jet Micro-EDM [PDF]

, 2013
Electrical discharge machining (EDM) is of the potential of micro/nano meter scale machining capability. However, electrode wear in micro-EDM significantly deteriorates the machining accuracy, thus, it needs to be compensated in process.
Xu, Kaixian, Zhao, Wansheng, Kang, Xiaoming   +2 more
core  

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

STUDY ON WIRE ELECTRICAL DISCHARGE MACHINING (WEDM) PROCESS UNDER THE CONDITIONS OF ULTRASONIC ACTIVATION OF THE DIELECTRIC FLUID

Nonconventional Technologies Review, 2022
In this paper, few mechanisms for removing material by Wire Electrical Discharge Machining (WEDM), with ultrasonic activated wire electrode are analyzed. Vibrations with an ultrasonic frequency of the wire electrode to the dielectric fluid from gap have
Viorel Mihai Nani, Dumitru Mnerie, Alin Nani   +2 more
doaj  

EXPERIMENTAL EVALUATION OF WEDM MACHINED SURFACE WAVINESS

Acta Polytechnica, 2016
Wire Electrical Discharge Machining (WEDM) an unconventional machining technology which has become indispensable in many industries. The typical morphology of a surface machined using the electrical discharge technology is characterized with a large ...
Katerina Mouralova, Jiri Kovar, Pavel Houska   +2 more
doaj   +1 more source

An overview to micro-wire-electrical discharge machining

IOP Conference Series: Materials Science and Engineering, 2021
Abstract Hard to cut metals are widely machined with the help of Wire EDM process which overcomes major challenges in the conventional machining processes. For generation of micro-features and complex three dimensional structures Wire EDM is considered above other unconventional machining process like abrasive jet, laser, plasma and ...
Rajesh K Porwal, K Vinod, Premanand S Chauhan, Rajendra K Shukla   +3 more
openaire   +1 more source

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source