Results 71 to 80 of about 6,389,749 (288)

Investigation of process parameters for stable micro dry wire electrical discharge machining [PDF]

, 2019
Micro dry wire electrical discharge machining (μDWEDM) is a process where gas is used as the dielectric fluid instead of a liquid. In this process, certain modifications of wire electrical discharge machining (WEDM) are needed during the machining ...
Abd Rahman, Md Nizam, Konneh, Mohamed, Banu, Asfana, Ali, Mohammad Yeakub   +3 more
core   +1 more source

Toward Perception‐Native Electronic Skin: Bio‐Inspired In‐/Near‐Sensor and Neuromorphic Computing for Humanoid Robots

Advanced Materials Technologies, EarlyView.
Dense tactile streams from across the humanoid body converge on collide in a central wiring and data bottleneck. By relocating computation closer to and then into the skin itself, near‐ and in‐sensor architectures, together with neuromorphic computing, chart a path toward perception‐native electronic skin, in which the conversion of stimulus into ...
Mijin Kim, Chang‐Jae Beak, Jiyoung Park, Youngdo Jung, Sunjong Oh, Sin‐Hyung Lee, Bo‐Yeon Lee   +6 more
wiley   +1 more source

Analysis of Material Removal and Surface Characteristics in Machining Multi Walled Carbon Nanotubes Filled Alumina Composites by WEDM Process

MATEC Web of Conferences, 2017
The reinforcement of ceramic materials with electrically conductive particles increases the overall conductivity of the ceramic material. This allows the ceramic material to be more readily machined using wire electrical discharge machining process.
Annebushan Singh Meinam, Kumar Sarma Deba, Mani Kalita Hriday, Marthong Comingstarful   +3 more
doaj   +1 more source

Verification of Fuzzy Inference System for Cutting Speed while WEDM for the Abrasion-Resistant Steel Creusabro by Conventional Statistical Methods

Metals, 2020
Wire electrical discharge machining is an unconventional machining method for the production of complex-shaped and very precise parts. Because of the high energy consumption of this machining process, it is necessary to maximize the cutting speed for its
Katerina Mouralova, Pavel Hrabec, Libor Benes, Jan Otoupalik, Josef Bednar, Tomas Prokes, Radomil Matousek   +6 more
doaj   +1 more source

Liquid Crystal Elastomer Actuator Matrix for Large Area Applications

Advanced Materials Technologies, EarlyView.
A scalable approach is used to manufacture a digitally‐controllable, 2D 5 × 5 actuator matrix. The elements of the matrix are produced by direct ink writing of a liquid crystal elastomer ‘artificial muscle’ on large‐area flexible thin‐film heaters. In optimizing the low‐power actuators, multiple heater designs and substrate materials are investigated ...
Giulia Spallanzani, Bart Peeters, Danqing Liu, Peter Zalar, Hylke B. Akkerman, Jeroen A. H. P. Sol   +5 more
wiley   +1 more source

Recent Advances in Transparent Microelectrode Device Architecture and Fabrication Strategies for Biomedical Applications

Advanced Materials Technologies, EarlyView.
Transparent microelectrode arrays enable simultaneous optical and electrical electrophysiology with high spatiotemporal resolution, allowing multimodal observations of dynamic biological systems. Advances in materials and device architectures improve device performance by addressing key trade‐offs between optical transparency, impedance, and ...
Michael Abraham Listyawan, Tran Bach Dang, Chi Cong Nguyen, Yee Lap Pong, Tianruo Guo, Thanh Nho Do, Hoang‐Phuong Phan   +6 more
wiley   +1 more source

Abrasion Assisted Wire Electrical Discharge Machining

, 2007
The adoption of Electrical Discharge Machining (EDM) technologies to mainstream manufacturing saw dramatic advances in the process starting in the 1980's.
Menzies, Ian
core   +1 more source

Performance of nanocomposite ceramics by wire electrical discharge machining

MATEC Web of Conferences, 2015
A new process of machining the TiN/Si3N4 nanocomposite ceramics using wire electrical discharge machining is proposed in this paper. The process is able to effectively machine a large surface area on the TiN/Si3N4 nanocomposite ceramics with good surface
Zhang Chengmao
doaj   +1 more source

Wire Electrical Discharge Machining

, 2012
The work deals with the technology of electrical discharge wire cutting. The first chapter describes the principle of EDM machining with the basic description of the methods using this machining technology.
Barabáš, Martin
core  

Soft Actuators Integrated with Control and Power Units: Approaching Wireless Autonomous Soft Robots

Advanced Robotics Research, EarlyView.
Soft robots exhibit significant development potential in various applications. However, there are still key technical challenges regarding material improvement, structure design and components integration. This review focuses on the development and challenge of soft actuators, power components, and control components in untethered intelligent soft ...
Renwu Shi, Feifei Pan, Xiaobin Ji
wiley   +1 more source