Results 91 to 100 of about 1,683,719 (278)

Fiber association and network formation in PLA/lignocellulosic fiber composites. [PDF]

, 2013
PLA composites were prepared in an internal mixer with a lignocellulosic fiber having relatively large aspect ratio. Fiber content changed between 0 and 60 vol% and the homogenized material was compression molded to 1 mm thick plates.
Renner, Károly, Pukánszky, Béla, Móczó, János, Faludi, Gábor, Hári, József   +4 more
core   +1 more source

Not Only Delicious: Papaya Bast Fibres in Biocomposites

BioResources, 2016
Previous studies have shown favourable properties for papaya bast fibres, with a Young's modulus of up to 10 GPa and a tensile strength of up to 100 MPa.
Thea Lautenschläger, Andreas Kempe, Christoph Neinhuis, André Wagenführ, Sebastian Siwek   +4 more
doaj   +1 more source

Multi‐Li+ Coordination for Superior Room‐Temperature Ionic Conductivity in PEO Solid Electrolytes

Advanced Materials, EarlyView.
A phosphonate‐functionalized polycarboxylate ether (P‐PCE) is introduced into PEO electrolytes to induce multi‐Li+ ions coordination, which effectively dissociates lithium salts, liberates Li+ from the strong chelation by PEO chains, and promotes fast Li+ hopping between adjacent coordination sites. Simultaneously, this design establishes dynamic, high‐
Hengming Yan, Bowen Zhang, Xuefan Liu, Lu Wang, Cunlong Hu, Anran Sheng, Congcong Zhang, Linglong Kong, Zhenzhen Wu, Yulin Zhong, Sheng Liu, Shanqing Zhang   +11 more
wiley   +1 more source

Ti3C2Tx MXene/Silver Composite Foams For Lightweight, High‐Performance Electromagnetic Interference Shielding and Joule Heating

Advanced Materials Interfaces, EarlyView.
Ultrathin MXene/EMF composite foams achieve a specific shielding efficiency of 749.6 dB.dB·cm3$\mathrm{dB}\cdot {\mathrm{cm}}^{3}$/g, while the silver‐enhanced MXene/Ag/EMF reaches 81.4 dB shielding effectiveness at just 1.0 mm thickness. Both composites exhibit rapid Joule heating, retain stability up to 250∘C$^\circ{\rm C}$, and withstand 1000 ...
Abdullah A. Mahmood, Mingxuan Li, Vahid Rad, Mehdi Zarei, Chen‐Yu Yeh, Masoud Soroush, Guangyong Li, Paul W. Leu   +7 more
wiley   +1 more source

Enhancement and Compatibilization of Waste-Sourced Biocomposites Through Elastomer Blending and Matrix Grafting Modification

Molecules
A novel elastomer-modified multicomponent, multiphase waste-sourced biocomposites, was prepared for converting waste biomass and plastic into value-added products. The effects of blending elastomer–olefin block copolymer (OBC) and maleic anhydride (MAH),
Shunmin Yi, Wanyu Liu, Shihua Xu, Ruijia Hu, Qing Li, Meijia Wu, Qingwen Wang, Zhimin Huang   +7 more
doaj   +1 more source

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

Advanced Manufacturing of Composite‐Based Systems for Energy Applications

Advanced Materials Technologies, EarlyView.
Advanced manufacturing enables the integration of polymers, ceramics, metal oxides, and composites into architected microstructures with tailored transport pathways. By coupling material selection, manufacturing strategy, and structural design, multifunctional energy systems can simultaneously improve electrochemical performance, thermal management ...
Sri Vaishnavi Thummalapalli, Dhanush Patil, Libin Yang, M. Taylor Sobczak, Anshul Kulkarni, Xiao Sun, Arunachalam Ramanathan, Tiantian Li, Ramaraja P. Ramasamy, Jason J. Locklin, Yanyu Chen, Xianqiao Wang, Arunachala Mada Kannan, Kenan Song   +13 more
wiley   +1 more source

Development of a Wood Plastic Composite Extruder

International Journal of Waste Resources, 2017
Wood plastic composites (WPC) is the recycling of wood flour and plastic into new products like particle boards, floor tiles and other structural building applications. An extruding machine is developed at the workshop of Agricultural and Environmental Engineering Department of The Federal University of Technology, Akure, Ondo State to handle the ...
WA Akinfiresoye, OJ Olukunle, AA Akintade   +2 more
openaire   +1 more source

Performance of waste-paper/PETG wood–plastic composites

AIP Advances, 2018
Wood–plastic composites were prepared from polyethylene terephthalate- 1,4-cyclohexanedimethanol ester (PETG) and waste-paper fiber that was unmodified, modified with alkyl-ketene-dimer (AKD), and modified with a silane-coupling agent.
Lijie Huang, Shuxiang An, Chunying Li, Chongxing Huang, Shuangfei Wang, Xiaoxiao Zhang, Mingzi Xu, Jie Chen, Lei Zhou   +8 more
doaj   +1 more source

Wood‐Derived Nanocellulose‐Biocarbon Fresnel‐Zone Plate Lenses for Sub‐THz Frequency Applications

Advanced Materials Technologies, EarlyView.
Wood‐derived nanocellulose and lignin‐based biocarbon were combined to fabricate fully bio‐based Fresnel zone plate (FZP) lenses for sub‐terahertz frequencies. These sustainable FZP lenses exhibit low dielectric loss and high directivity, achieving performance comparable to that of metallic references, and remain functional under environmental stress ...
Riikka Haataja, Mikko Kokkonen, Niina Halonen, Sami Myllymäki, Umair Rafique, Mandeep Singh, Ossi Laitinen, Heli Jantunen, Kristiina Oksman, Henrikki Liimatainen   +9 more
wiley   +1 more source