Results 11 to 20 of about 1,163,826 (301)
A Plackett-Burman Design to Optimize Wood Chipper Settings [PDF]
Croatian Journal of Forest Engineering, 2019 The wood-chipping process is affected by several factors, notably chipper settings and wood characteristics. It is often difficult to test all of these factors in a full factorial experimental plan, due to the large number of trials required.
Lorenzo Guerrini +6 more
doaj +2 more sources
In situ high-temperature gas sensors: continuous monitoring of the combustion quality of different wood combustion systems and optimization of combustion process [PDF]
Journal of Sensors and Sensor Systems, 2018 The sensing characteristics and long-term stability of different kinds of CO ∕ HC gas sensors (non-Nernstian mixed potential type) during in situ operation in flue gas from different types of low-power combustion systems (wood-log- and wood-chip ...
H. Kohler +6 more
doaj +1 more source
Effect of different wood species on heterocyclic aromatic amine level in Harbin red sausages
Food Science of Animal Products, 2023 The influence of different wood species (in the form of wood chips) on the formation of heterocyclic aromatic amines (HAAs) in smoked Harbin red sausages was investigated. Four common species of wood (pear, oak, apple, beech) were used for smoking.
Xiaoyu Yin +4 more
doaj +1 more source
Jurnal Sylva Lestari, 2023 Wood biomass such as sawdust, particles, and chip obtained wood industry can be used as raw material for chip block pallets (CBP). This study evaluated the resistance of chip block pallets made from teak-sawn waste and polyurethane adhesive against decay
Alessandro Geovani Damanik +8 more
doaj +1 more source
Sieving and Covering of Wood Chips Improves Storability [PDF]
Energies, 2022 Minimising dry matter losses during storage of comminuted forest fuels is desirable from both an economic and a sustainability perspective. This study examined fuel quality and amount of recovered energy during the storage of forest wood chips stored at full industrial scale at three locations, and the effect of sieving and covering piles with a water ...
Anerud, Erik +4 more
openaire +3 more sources
A review of wood machining literature with a special focus on sawing [PDF]
, 2013 In this review, fundamental wood machining research is evaluated to determine the general cutting mechanics of simple, orthogonal, and oblique cutting tools. Simple tool force trends and chip formation characteristics are indentified here, along with the
Phil Hackney +5 more
core +1 more source
Cutting Forces and Chip Morphology during Wood Plastic Composites Orthogonal Cutting
BioResources, 2014 The effect of chip thickness, rake angle, and edge radius on cutting forces and chip morphology in wood plastic composites (WPCs) orthogonal cutting was investigated.
Xiaolei Guo +5 more
doaj +1 more source
Journal of Wood Science, 2021 The paper proposes the use of microwave irradiation to lower the initial moisture content of wood chips. The study involved willow and fir chips fractionated by means of a sieve separator and unfractionated ash chips.
Monika Aniszewska +3 more
doaj +1 more source
Grindability of torrefied wood chips and wood pellets
Fuel Processing Technology, 2018 Abstract Torrefaction of biomass improves the grindability of raw biomass by the transformation from a fibrous structure to a more brittle and friable, coal-like material. Torrefied biomass is a more desirable feedstock for co-firing applications, especially in existing coal-fired power plants.
Maryam Manouchehrinejad +2 more
openaire +1 more source
Color Removal of Pulp and Paper Mill Wastewater Using Residual Eucalyptus Wood
Environment and Natural Resources Journal, 2022 This study investigated the color removal efficiency of pulp and paper mill wastewater using residual eucalyptus wood as a method to minimize the solid wastes generated from pulp and paper processes.
Kanjana Yupin +4 more
doaj +1 more source