Results 221 to 230 of about 2,631,798 (305)

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

The effects of mixed-mode ventilation on energy saving and employee job satisfaction, work engagement, and job performance. [PDF]

Sci Rep
Min Ye Y, Liang W, Xu F, Chong A, Barnes CM, Yam KC.   +5 more
europepmc   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

A contribution to the Italian validation of the occupational hardiness scale and its role in work engagement and emotional exhaustion. [PDF]

Sci Rep
Panari C, Mazzetti G, Lo Piccolo E, Guglielmi D, Simbula S.   +4 more
europepmc   +1 more source

Productivity‐Driven Optimization of Laser Powder Bed Fusion Parameters for IN718 Superalloy: Process Control, Microstructure, and Mechanical Properties

Advanced Engineering Materials, EarlyView.
This study demonstrates how optimizing laser power, scanning speed, and hatching distance in laser powder bed fusion can boost the productivity of Inconel 718 manufacturing by up to 29% while maintaining mechanical integrity. The work delivers a validated process window and cost–time analysis, offering industry‐ready guidelines for efficient additive ...
Amir Behjat, Guido Barale, John Stavridis, Ehsan Norouzi, Jin‐Yoo Suh, Dong‐Ik Kim, Luca Iuliano, Abdollah Saboori   +7 more
wiley   +1 more source

The impact of hindrance-challenge stress on nurses' work engagement: a cross-sectional study. [PDF]

BMC Nurs
Zhou M, Lin Z, Xu J, Wang Q, Bian W, Li F, Chen L.   +6 more
europepmc   +1 more source

Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows

Advanced Engineering Materials, EarlyView.
A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba, Sang‐Hyeok Lee, Christina Gasper, Martina Freund, Sandra Korte‐Kerzel, Ulrich Kerzel   +5 more
wiley   +1 more source

Association Between Psychological Empowerment and Work Engagement Among Rural Nurses: A Latent Profile and Moderation Analysis. [PDF]

J Nurs Manag
Xu E, Huang H, Zhou Y, Tang W.
europepmc   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

Nurses' Perception of the Effect of Motivation, Psycho-Social Safety Climate, and Work Engagement: A Mediation Analysis. [PDF]

Nurs Rep
Hossny EK, Aboelmagd NS, Aly SE, Elnaeem MMA, El-Aty NSA, Mahmoud AM, Alsheikh Mohamed I, Ahmed AM.   +7 more
europepmc   +1 more source