Results 41 to 50 of about 763,123 (301)

Effect of Cu Content on TiN-Cu Nanocomposite Film Properties: Structural and Hardness Studies [PDF]

Journal of Nanostructures, 2013
Titanium nitride-Copper (TiN-Cu) nanocomposite films were deposited onto stainless steel substrate using hollow cathode discharge ion plating technique. The influence of Cu content in the range of 2-7 at.% on the microstructure, morphology and mechanical
M. M. Larijani, P. Balashabadi, H. Seyedi, E. Jafari-.Khamse   +3 more
doaj   +1 more source

Trace Nickel Activated Biphasic Core‐CuOii/Shell‐CuOi Secondary Microspheres Enable Room Temperature Parts‐Per‐Trillion‐Level NO2 Detection

Advanced Engineering Materials, EarlyView.
An idea of designing novel sensors is proposed by creating appropriate Schottky barriers and vacancies between isomorphous Core‐CuOii/ Shell‐CuOi secondary microspheres and enhancing catalytic and spill‐over effects, and electronegativity via spontaneous biphasic separation, self‐assembly, and trace‐Ni‐doping.
Bala Ismail Adamu, Peipei Chen, Shafia Mukhtar Ibrahim, Mukhtar Lawan Adam, Attia Falak, Mokhotjwa Simon Dhlamini, Hanfu Wang, Lingxiang Jiang, Weiguo Chu   +8 more
wiley   +1 more source

Electrochemical deposition of Mg(OH)2/GO composite films for corrosion protection of magnesium alloys

Journal of Magnesium and Alloys, 2015
Mg(OH)2/graphene oxide (GO) composite film was electrochemical deposited on AZ91D magnesium alloys at constant potential. The characteristics of the Mg(OH)2/GO composite film were investigated by scanning electron microscope (SEM), energy-dispersive X ...
Fengxia Wu, Jun Liang, Weixue Li
doaj   +1 more source

Magnetic non-uniformity and thermal hysteresis of magnetism in a manganite thin film

, 2011
We measured the chemical and magnetic depth profiles of a single crystalline (La$_{1-x}$Pr$_x$)$_{1-y}$Ca$_y$MnO$_{3-{\delta}}$ (x = 0.52\pm0.05, y = 0.23\pm0.04, {\delta} = 0.14\pm0.10) film grown on a NdGaO3 substrate using x-ray reflectometry ...
Biswas, A., Fitzsimmons, M. R., Jeen, H., Lookman, T., Roldan, M. A., Singh, Surendra, Thompson, J. D., Varela, M.   +7 more
core   +1 more source

An Inkjet‐Printed Platinum‐Based Temperature Sensing Element on Polyimide Substrates

Advanced Engineering Materials, EarlyView.
An inkjet‐printed, meander‐structured, nanoparticle platinum‐based resistive temperature sensors on polyimide substrates are demonstrated as proof‐of‐concept. Optimized sintering at 250°C enables stable conductive structures. The Pt100‐ and Pt1000‐type sensors exhibit linear resistance–temperature characteristics with stable TCR in the 20°C–80°C range,
Shawon Alam, Thomas Kister, Alexander Scholz, Sophie Sauva, Makara Lay, Tobias Kraus, Jasmin Aghassi‐Hagmann   +6 more
wiley   +1 more source

The accuracy of single emulsion radiographic film in linear measurement of spiral tomography

Dental Research Journal, 2013
Background: Conventional tomography used for evaluation of the small areas of the jaws provides acceptable information. It has some advantages of availability, less radiation dose and cost in comparison to computed tomography (CT) and cone beam CT ...
Arash Dabbaghi, Ali Shokraneh, Nastaran Farhadi   +2 more
doaj   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Tunable sub-luminal propagation of narrowband x-ray pulses [PDF]

, 2014
Group velocity control is demonstrated for x-ray photons of 14.4 keV energy via a direct measurement of the temporal delay imposed on spectrally narrow x-ray pulses. Sub-luminal light propagation is achieved by inducing a steep positive linear dispersion
Di Piazza, A., Formanek, M., Franke, P., Froula, D. H., Malaca, B., Mori, W. B., Palastro, J. P., Pierce, J. R., Ramsey, D., Simpson, T. T., Vieira, J., Vranic, M., Weichman, K.   +12 more
core   +3 more sources

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Digital radiology to improve the quality of care in countries with limited resources: a feasibility study from Angola.

PLoS ONE, 2013
ObjectiveSub-standard quality in X-ray image acquisition and interpretation is common in low-resource countries, and can ultimately result in higher patient morbidity and mortality. This study aimed at evaluating; 1) feasibility of implementing a digital
Floriana Zennaro, Joaquim António Oliveira Gomes, Armando Casalino, Magda Lonardi, Meta Starc, Pierpaolo Paoletti, Daniele Gobbo, Chiara Giusto, Tarcisio Not, Marzia Lazzerini   +9 more
doaj   +1 more source