Results 161 to 170 of about 30,167,678 (291)

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

THE X-RAY PHASE ANALYSIS OF MIKALEKSOVY COMPOSITION WITH THE NEW BINDING [PDF]

Theoretical & Applied Science, 2015
Svetlana Valeryevna Fedorova, Inna Aleksandrovna Serebryanik   +1 more
openaire   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Artifact segmentation using the U-Net architecture for powder X-ray diffraction images. [PDF]

J Synchrotron Radiat
Vong A, Yanxon H, Roberts E, Parraga H, Weng J, Xu W, Ruett U, Hexemer A, Zwart PH, Schwarz N.   +9 more
europepmc   +1 more source

The X-ray reflectometry and the phase contrast methods for crystal analysis [PDF]

Acta Crystallographica Section A Foundations of Crystallography, 2005
A. Kryazhev, A. P. Petrakov
openaire   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

From Synthesis to Failure: In Situ Characterization of Lithium-Ion Battery Cathodes. [PDF]

Small
Zhao X, Lou J, Gao J, Pang S, Wang L, Wang L, Wang Y, Xu Y, Cheng D, He X, Shen J.   +10 more
europepmc   +1 more source

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

Influence of Cathode Origin on the Crystallization of LiNbO₃ Coatings on Ni-Rich Layered Oxides. [PDF]

Chempluschem
Mereacre V, Guo Y, Xu R, Hansen AL, Knapp M, Ehrenberg H, Binder JR.   +6 more
europepmc   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source