Results 51 to 60 of about 656,556 (303)
Biocalcarenites as construction materials in Santa Marina de Aguas Santas Church at Cordoba, Spain
Materiales de Construccion, 2009 This study consisted in characterizing the materials used to build Santa Marina de Aguas Santas Church at Cordoba and locating the original quarries.
J. Barrios Neira +4 more
doaj +1 more source
Gazi Üniversitesi Fen Bilimleri Dergisi, 2020 Sample preparation is one of the main steps in metallographic examinations and the sample preparation processes give rise to changes in the determination of volume fraction of any phases can cause failure at the interpretation of a study.
Burak NALÇACI +2 more
doaj +1 more source
Non-destructive characterisation of fine grained samples: assessment of insitu micro-XRD of primitive meteorite matrix [PDF]
, 2014 No abstract ...
Franchi, I.A. +4 more
core
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Evolution of the hydration in cements with additions
Materiales de Construccion, 2002 In this paper, the hydration mechanism of portland cement pastes with limestone, quartz and natural pozzolan (80/20 weight) was analized. The techniques used were nonevaporable water content, pozzolanic activity and X-ray diffraction.
V. L. Bonavetti +2 more
doaj +1 more source
Journal of Natural Fibers, 2022 Appropriate surface modifications are required to enhance the compatibility of natural fibers with polymer matrix to develop eco-friendly composites. One of such novel plant fibers is Bauhinia vahlii (BV) stem fiber.
Umakanta Patel +4 more
doaj +1 more source
Phase composition and transformations in magnetron-sputtered (Al,V)2O3 coatings
, 2019 Coatings of (Al1-xVx)2O3, with x ranging from 0 to 1, were deposited by pulsed DC reactive sputter deposition on Si(100) at a temperature of 550 {\deg}C. XRD showed three different crystal structures depending on V-metal fraction in the coating: {\alpha}-
Ahlgren, M. +9 more
core +1 more source
Effect of TiO2 addition on structure, solubility and crystallisation of phosphate invert glasses for biomedical applications [PDF]
, 2010 NOTICE: this is the author’s version of a work that was accepted for publication in JOURNAL OF NON-CRYSTALLINE SOLIDS. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality ...
Abrahams +28 more
core +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Proceedings of the International Conference on Applied Innovations in ITIndium-doped ZnS samples with doping levels of 0%, 1%, and 3% were fabricated using the chemical spray pyrolysis (CSP) method. XRD patterns confirmed the presence of a cubic zinc blend structure of both pure and Indium-doped ZnS samples.
Tahseen H. Mubarak +7 more
doaj +1 more source