Results 51 to 60 of about 70,306 (261)
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
The Extreme Values of Young’s Modulus and the Negative Poisson’s Ratios of Rhombic Crystals
, 2021 The extreme values of Young’s modulus for rhombic (orthorhombic) crystals using the necessary and sufficient conditions for the extremum of the function of two variables are analyzed herein.
Dmitry S. Lisovenko +1 more
core +1 more source
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
, 2018 Open-cell specimens, densities, porosities, mean experimental Young’s modulus [34] and the mean computational Young’s modulus [34].
Samuel Jesús Ramos-Infante (5391065) +3 more
core +1 more source
Correlation of dynamic and static young’s modulus for limestone [PDF]
, 2022 The application of rock mechanics in the area of geotechnical engineering is important especially, in describing the strength of rock material for essessing the stability of excavations, foundations and slopes in rock. In this study, the characterization
Abdul Ghani Rafek +9 more
core
Nanomaterials, 2021 The accurate measurement of nanoscale mechanical characteristics is crucial in the emerging field of soft condensed matter for industrial applications. An atomic force microscope (AFM) can be used to conduct nanoscale evaluation of the Young’s modulus on
Seongoh Kim +4 more
doaj +1 more source
Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines
Advanced Engineering Materials, EarlyView.Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl +4 more
wiley +1 more source
BioengineeringScaffolds are critical in regenerative medicine, particularly in bone tissue engineering, where they mimic the extracellular matrix to support tissue regeneration.
Rixiang Quan +2 more
doaj +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source