Results 31 to 40 of about 30,907 (217)
Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses
Advanced Engineering Materials, EarlyView.Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk +4 more
wiley +1 more source
PLoS ONE, 2023 ObjectivesThis study aimed to evaluate the color stability and translucency of various types of monolithic zirconia after immersion in chlorhexidine and Listerine mouthwashes.Materials and methodsThis experimental study was performed on 36 disk-shaped ...
Rashin Giti, Reza Jebal
doaj +1 more source
Advanced Functional Materials, EarlyView.A scalable, solution‐processed WSe2/ZrO2‐x van der Waals heterostructure realizes a light‐induced field‐tunneling synapse (LIFTS) that activates exclusively under bright illumination, emulating the photopic adaptation of the human retina at the device level.
Kijeong Nam +10 more
wiley +1 more source
Comparison of the effect of monolithic and layered zirconia on natural teeth wear: An in vitro study
The Journal of Indian Prosthodontic Society, 2018 Aim: The aim of this study is to compare wear of the natural teeth against monolithic zirconia and layered zirconia with different surface finishing procedures such as unpolished unglazed, polished unglazed, and polished glazed.
Yamini Gundugollu +5 more
doaj +1 more source
Preparation of inverse opal zirconia [PDF]
Science of Sintering, 2018 Inverse opal zirconia is useful in many ways because of their ability to combine several chemical and physical properties. In this research, polystyrene template was fabricated by self-assembly method and inverse opal zirconia was prepared by ...
Li Xiao-Peng +4 more
doaj +1 more source
Advanced Functional Materials, EarlyView.A spatial location of atomic layer deposition (ALD)‐derived ZrO2 coatings is demonstrated to be a critical design parameter for stabilizing graphite cathodes in DIBs. Direct particle‐level ALD (PALD) screening of representative metal oxides identified ZrO2 as the coating that provides the most favorable balance of high‐rate capability and interfacial ...
Jieun Kang +7 more
wiley +1 more source
BMC Oral HealthBackground Monolithic zirconia restorations have emerged as a viable alternative to veneered zirconia restorations, eliminating the risk of veneer chipping due to their superior strength, fracture resistance, and aesthetics.
Sara Ismail Mohamed Hussein +2 more
doaj +1 more source
Radiative Thermal Management for Extreme Environments: Mechanisms and Design Strategies
Advanced Materials, EarlyView.In this review, we discuss the fundamental mechanisms of radiative cooling and solar heating, material and structural design strategies, hybrid approaches integrating additional heat transfer pathways, and durability‐oriented designs addressing environmental stresses.
Hyung Rae Kim +5 more
wiley +1 more source
Advanced Materials, EarlyView.Development of a novel method for synthesizing Ni single atom catalysts for highly selective electrochemical CO2 reduction in situ. This catalyst achieves 100% selectivity for CO and is formed in an industrially relevant cell architecture. Using post‐mortem XRD, STEM, and EDS and operando XAS, the identity of the active site and the mechanism behind ...
Ian Street +5 more
wiley +1 more source
Cells, 2023 Soft tissue adhesion and sealing around dental and maxillofacial implants, related prosthetic components, and crowns are a clinical imperative to prevent adverse outcomes of periodontitis and periimplantitis.
Toshikatsu Suzumura +5 more
doaj +1 more source