Results 81 to 90 of about 714,548 (303)
Contrasting Decollement and Prism Properties over the Sumatra 2004-2005 Earthquake Rupture Boundary [PDF]
, 2010 Styles of subduction zone deformation and earthquake rupture dynamics are strongly linked, jointly influencing hazard potential. Seismic reflection profiles across the trench west of Sumatra, Indonesia, show differences across the boundary between the ...
Ammon +16 more
core +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Optimized Design of Anchor Plates for 2200 MPa-Class Prestressing Anchorage Zones
BuildingsThe strength of prestressed steel strands has developed towards high strength, increasing from 1860 MPa to over 2200 MPa. The stress in the prestressed anchorage zone is more concentrated and complex, and the anchor plates for dispersed loads need to be ...
Xin Lu, Wanxu Zhu
doaj +1 more source
Geometry and seismic properties of the subducting Cocos plate in central Mexico [PDF]
, 2010 The geometry and properties of the interface of the Cocos plate beneath central Mexico are determined from the receiver functions (RFs) utilizing data from the Meso America Subduction Experiment (MASE).
Clayton, R. W., Jackson, J. M., Kim, Y.
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Optimization of a finite element mesh for plates subjected to in-plane patch loading [PDF]
, 2019 In designing in-plane stressed thin plates, the loading condition where the uniform distributed edge forces are locally applied along one or more of the plate’s boundaries is often encountered. We investigated the optimal grid pattern that can be used in
Ikhenazen, Ghania +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.High‐frequency (HF) welding of steel is limited by oxide inclusions that degrade weld quality. This study demonstrates, for the first time, the integration of a nonthermal Ar/H2 dielectric barrier discharge (DBD) plasma jet into HF welding. Local plasma treatment provides effective shielding and in‐situ oxide reduction, resulting in markedly fewer and ...
Viktor Udachin +4 more
wiley +1 more source
Journal of Orthopaedic Surgery and ResearchBackground No clear agreement exists on the degree of bone formation required to remove a metal plate without correction loss after medial opening-wedge high tibial osteotomy (MOWHTO).
Chul-Young Jang +6 more
doaj +1 more source
Generation of the squamous epithelial roof of the 4th ventricle
eLife, 2019 We use the transparency of zebrafish embryos to reveal the de novo generation of a simple squamous epithelium and identify the cellular architecture in the epithelial transition zone that ties this squamous epithelium to the columnar neuroepithelium ...
Florent Campo-Paysaa +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source