Results 171 to 180 of about 2,087 (230)
Some of the next articles are maybe not open access.
Рекомбинантный S-белок SARS-CoV-2 in vitro способен связывать гликаны семейства лактозамина
, 2021А. Б. Рыжиков+9 more
semanticscholar +1 more source
Доклады Российской академии наук. Науки о жизни, 2021
Людмила Сергеевна Мельникова+4 more
semanticscholar +1 more source
Людмила Сергеевна Мельникова+4 more
semanticscholar +1 more source
2018
РвÑпÑÑкной квалиÑикаÑионной ÑабоÑе бакалавÑа опиÑана оÑÐ½Ð¾Ð²Ð½Ð°Ñ Ð´ÐµÑÑелÑноÑÑÑ Ð¾ÑганизаÑии, оÑÑÐ°Ð¶ÐµÐ½Ñ ÑÐµÑ Ð½Ð¸ÐºÐ¾-ÑкономиÑеÑкие и ÑинанÑовÑе показаÑели, иÑÑледована оÑганизаÑÐ¸Ñ Ð»Ð¾Ð³Ð¸ÑÑиÑеÑкой деÑÑ ...
openaire +1 more source
РвÑпÑÑкной квалиÑикаÑионной ÑабоÑе бакалавÑа опиÑана оÑÐ½Ð¾Ð²Ð½Ð°Ñ Ð´ÐµÑÑелÑноÑÑÑ Ð¾ÑганизаÑии, оÑÑÐ°Ð¶ÐµÐ½Ñ ÑÐµÑ Ð½Ð¸ÐºÐ¾-ÑкономиÑеÑкие и ÑинанÑовÑе показаÑели, иÑÑледована оÑганизаÑÐ¸Ñ Ð»Ð¾Ð³Ð¸ÑÑиÑеÑкой деÑÑ ...
openaire +1 more source
Белок ядрышка SURF6 – известные свойства и возможные функции
, 2021А. А. Моралева+3 more
semanticscholar +1 more source
This work is dedicated to the study of methods for automating the detection of defects in stencil printing of films. The tasks that were solved during the study: 1. Study of possible defects in stencil printing. 2. Search for the optimal method of defect detection. 3. Development of hardware implementation for the defect detection task. 4.
openaire +1 more source
openaire +1 more source
2016
Emission-active thin carbon films grown at monocrystalline silicon substrates were studied by the methods of scanning tunneling microscopy and tunneling spectroscopy. Spatial non-uniformity of photoirradiation effect onto electric properties has been detected.
openaire +1 more source
Emission-active thin carbon films grown at monocrystalline silicon substrates were studied by the methods of scanning tunneling microscopy and tunneling spectroscopy. Spatial non-uniformity of photoirradiation effect onto electric properties has been detected.
openaire +1 more source
Currently, 3D-printing technologies are gaining more and more popularity. 3D printed parts are already being introduced into mass production. There is software that allows you to design products and prepare models for 3D-printing. But in order to print a model, it is not enough to simply model it.
openaire +1 more source
openaire +1 more source
Формирование белок-липидных доменов в плазматических мембранах
Четырнадцатая международная мультиконференция : Тез. докл.semanticscholar +1 more source