Results 71 to 80 of about 74,346,148 (200)

Corrosion Fatigue of 17-4pH Stainless Steel in a Simulated Sea Water Solution

open access: yesJournal of Advanced Materials in Engineering, 2019
Since martensitic precipitation hardened 17-4pH stainless steel has been widely used in corrosive environments, evaluation of its corrosion fatigue behavior is important. In this research, after microstructural studies, mechanical, corrosion, fatigue and
M. Ghasemian Malakshah   +3 more
doaj  

Extremely Low Cycle Fatigue Behavior of Additively Manufactured 17-4PH Stainless Steel [PDF]

open access: yes, 2020
Steel structures survive seismic loading thanks to components capable of dissipating large amounts of energy through large deformations. Future optimizations of these components include complex free-form geometries that are difficult to fabricate with ...
Collins, Kaley
core   +3 more sources

Precipitation and fracture in a ferritic stainless steel [PDF]

open access: yes, 2000
Includes bibliographical references.A dual stabilised ferritic stainless steel with titanium and niobium additions had been experiencing failures during production. Following hot rolling and cooling while coiled and prior to annealing, the steel had been
Scott, Adam James Lidstone
core   +1 more source

Characterization of CrMnNi Steel Powders Obtained via Gas Atomization

open access: yessteel research international, Volume 96, Issue 5, May 2025.
In this research article, the dependence of the properties of stainless‐steel powders obtained by gas atomization on the particle size is shown. Also, in this article, the morphology, particle size distribution, microstructure, and phase composition, as well as the change in chemical composition and surface tension of various powders fraction, are ...
Anastasiia Sherstneva   +4 more
wiley   +1 more source

Densification, deformation, and delamination during co‐sintering process of metal–ceramic laminates

open access: yesJournal of the American Ceramic Society, Volume 108, Issue 2, February 2025.
Abstract Today, there is a high demand and increasing trend for multifunctional composite materials and components due to the combination of a wide range of favorable properties. However, undesired deformation leading to delamination, curvature, cracks, or even complete fracture frequently occurs during the co‐sintering process of metal–ceramic ...
Chao Liu   +5 more
wiley   +1 more source

Characterization of the Corrosion of Nanostructured 17-4PH Stainless Steel by Surface Mechanical Attrition Treatment (SMAT)

open access: yes, 2019
The corrosion properties of nanostructured 17-4PH stainless steel facilitated by a surface mechanical attrition treatment (SMAT) process were studied using electrochemical measurements in 0.6 M NaCl aqueous solution.
Olugbade, Temitope Olumide; id_orcid   +3 more
core   +1 more source

Understanding the Effects of Manufacturing Attributes on Damage Tolerance of Additively Manufactured Parts and Exploring Synergy Among Process‐Structure‐Properties. A Comprehensive Review

open access: yesEngineering Reports, Volume 6, Issue 11, November 2024.
ABSTRACT Additive Manufacturing (AM) has revolutionized the production industry by offering design freedom with shorter lead times and reduced material wastage. However, the damage tolerance (DT) of AM parts is a significant concern due to their microstructural and geometric complexities, which affect their mechanical performance.
Zia Uddin   +4 more
wiley   +1 more source

Effect of double aging treatment on the tribological properties of 15-5PH coating on 17-4PH stainless steel by laser cladding

open access: yesJournal of Materials Research and Technology
To enhance the wear resistance of 17-4PH stainless steel, 15-5PH coatings are initially applied to its surface utilizing laser cladding technology. Subsequently, a double aging treatment is implemented as a post-processing method to further improve its ...
Hongxi Chen   +4 more
doaj   +1 more source

Process Parameter Optimization of Directed Energy Deposited QT17‐4+ Steel

open access: yesAdvanced Materials Technologies, Volume 9, Issue 15, August 7, 2024.
A novel QT17‐4+ stainless steel powder is used in directed energy deposition (DED), for the first time. Process parameters are optimized by the response surface methodology (RSM). The microstructure, level of porosity, phase content, and anisotropy in mechanical properties are characterized.
Vyas Mani Sharma   +5 more
wiley   +1 more source

Study the potential of micro laser sintering additive manufacturing technology for metallic 3D printing horn antenna structure

open access: yesThe Journal of Engineering, Volume 2024, Issue 8, August 2024.
Abstract Applications for an antenna structure produced with additive manufacturing technology are numerous and promising. This study focuses explicitly on utilizing micro‐laser sintering (MLS) three‐dimensional (3D) printing technology to fabricate two rectangular horn antennas identical to a standard Pasternack® horn antenna, making the fabrication ...
Sheikh Dobir Hossain   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy