Results 61 to 70 of about 38,847 (163)
Jixie qiangduObjectiveTo investigate the hardness and wear resistance of 18CrNiMo7-6 alloy steel and its surface modification layer after carburizing heat treatment.MethodsRepeated scratch tests were conducted using a Vickers indenter on both the 18CrNiMo7-6 alloy ...
PENG Teng +4 more
doaj
Residual stresses in 18CrNiMo7-6 linear friction welded high strength steel chains
The International Journal of Advanced Manufacturing Technology, 2018 Linear friction welding is a solid-state process that comprises rapid heating and cooling of the welded parts. Residual stresses (RS) as in every other welding process cannot be avoided. The presence of RS compromises the in-service performance and reliability.
Garcia Nunes, Dinis +5 more
openaire +4 more sources
Zjawisko pasmowości w odkuwkach ze stali 18CrNiMo7-6
, 2009 18CrNiMo7-6 steel, after hot forging, exhibits a distinct banding of ferritic-pearlitic microstructure, probably related to the segregation of alloying elements during the ingot crystallization.
Pawłowski, B., Krawczyk, J., Bała, P.
core
Evolution of Inclusions in Gear Steel 18CrNiMo7-6 during 70 t EAF-LF-RH Smelting Process
Teshugang, 2022 The evolution of inclusions in gear steel 18CrNiMo7-6 produced by 70 t EAF + LF + RH process is systematically analyzed and studied by means of whole process sampling and ASPEX test.
胡梦頔
doaj
Quality of semi-finished steel product 18CrNiMo7-6 of carburized gears for wind energetics
, 2012 Teoretická část diplomové práce se zabývá větrnou energetikou, druhy převodovek, materiály používanými pro ozubená kola, cementováním a nitrocementováním a napětími a deformacemi. Experimentální část je zaměřena na posouzení vlastností polotovarů z oceli
Hrdlička, Václav
core
Materials Research ExpressThe application of abrasive water jet (AWJ) technology is prevalent in enhancing the surfaces of intricate and high-strength components, thereby augmenting their resistance to fatigue.
Lan-rong Liu +5 more
doaj +1 more source
The new joint Australian and New Zealand design standard for steel and composite bridges AS/NZS 5100.6 - Part 6 : Steel and composite construction [PDF]
, 2020 This paper presents some of the innovations that are included within the new Bridge Design Standard for Steel and Composite Construction AS/NZS 5100.6, which will be the first harmonized standard between Australia and New Zealand for the design of ...
Hicks, Stephen J. +4 more
core
Structural behaviour of elliptical hollow sections under combined compression and uniaxial bending [PDF]
, 2011 The structural behaviour of elliptical hollow sections (EHS) has been examined in previous studies under the isolated loading conditions of pure compression and pure bending.
Chan, TM +8 more
core +1 more source
Analysis of composite concrete steel column using new steel section [PDF]
, 2021 Conventional concrete encased steel composite columns are typically constructed by embedded “W” steel section or other sections identified in the American Institute of Steel Construction “AISC”, positioned in the center of the concrete column cross ...
Abu Sharea, Ahmad
core
Banded microstructure in forged 18CrNiMo7-6 steel
Tyt. z nagłówka.Bibliografia s.[53].Dostępny również w formie drukowanej.ABSTRACT: 18CrNiMo7-6 steel, after hot forging, exhibits a distinct banding of ferritic-pearlitic microstructure, probably related to the segregation of alloying elements during the
Krawczyk, Janusz Ryszard.
core