Gefügeaufbau und mechanische Eigenschaften nach Einsatzhärten außerhalb des üblichen Parameterfeldes [PDF]
, 2019 A large part of the components used today, for example in gearbox construction, such as gears or bearing components, is adjusted to the stress during operation in a mostly thermochemical heat treatment process (usually gas carburizing).
Saddei, Peter
core
Simulationsforum 2013 - Schweißen und Wärmebehandlung [PDF]
, 2014 Das Buch veröffentlicht 22 Fachbeiträge der Konferenz "Simulationsforum 2013 - Schweißen und Wärmebehandlung"
Brand, Marcus +3 more
core
Jixie qiangduObjectiveTo investigate the hardness and wear resistance of 18CrNiMo7-6 alloy steel and its surface modification layer after carburizing heat treatment.MethodsRepeated scratch tests were conducted using a Vickers indenter on both the 18CrNiMo7-6 alloy ...
PENG Teng +4 more
doaj
The Influence of Surface Finish on the Localized Dissipation of Frictional Power at Ultra-Mild Wear [PDF]
, 2015 Tribological systems are subjected to a steady decrease of friction and wear due to ecological and economical requirements. These guidelines can change the tribological loads and, therefore, result in more severe conditions. The need for maintaining wear
Stickel, Daniel
core
Evolution of Inclusions in Gear Steel 18CrNiMo7-6 during 70 t EAF-LF-RH Smelting Process
Teshugang, 2022 The evolution of inclusions in gear steel 18CrNiMo7-6 produced by 70 t EAF + LF + RH process is systematically analyzed and studied by means of whole process sampling and ASPEX test.
胡梦頔
doaj
Abrasive Wear, Scuffing and Rolling Contact Fatigue of DLC-Coated 18CrNiMo7-6 Steel Lubricated by a Pure and Contaminated Gear Oil. [PDF]
Materials (Basel), 2021 Tuszyński W +6 more
europepmc +1 more source
EFFECTS OF SHOT PEENING ON HARDNESS OF 18CRNIMO7-6 STEEL BASED ON FINITE ELEMENT ANALYSIS
Jixie qiangdu, 2022 So far, most of the numerical studies on shot peening are limited in the effects of shot peening parameters on the residual stress and surface morphology. There is still lack of numerical research on shot peening parameters on the hardness.
CHEN HaiKuan +3 more
doaj
Gabungan Quenching-Variasi Tekanan Shot peening Terhadap Kekerasan Permukaan dan Struktur Mikro Permukaan Baja S45C [PDF]
, 2022 The combination of Quenching and Shot peening (SP) heat treatment is rarely carried out, especially the use of this treatment can improve the mechanical properties of medium carbon steel (S45C).
Margono, Margono +2 more
core
Hybrid methodology development for lubrication regimes identification based on measurements, simulation, and data clustering [PDF]
The lubrication regimes of a laboratory scale journal bearing were analysed with wide band acoustic emission (AE) measurements. The analysis was supported by data-based clustering of AE data. Digital twin of the journal bearing was generated with Simpack
Junttila, Jukka +4 more
core +2 more sources
HEAT AFFECTED ZONE MICROSTRUCTURE OF WELD JOINT PREPARATION IN ARTIFICIAL MANNER [PDF]
, 2019 This paper presents two possibilities of martensitic (fine grain and coarse grain) microstructure preparation. These microstructures are present as sub-zones in the heat-affected zone of welded joints, but due to the narrow region of HAZ in a real weld ...
Gjelaj, Afrim +3 more
core +1 more source