Results 91 to 100 of about 13,916,515 (311)

3D Beamforming for Improving the Security of UAV-Enabled Mobile Relaying System [PDF]

Radioengineering, 2019
In this paper, we consider an unmanned aerial vehicle (UAV)-enabled mobile relaying system consists of a ground control station (GCS), a high-mobility UAV for relaying, a destination, and an eavesdropper.
Q. Yuan, Y. Hu, C. Wang, X. Ma
doaj  

A Thermodynamic 3D Model for the Simulation of Diffusion‐Controlled Alloying Processes in Heterogeneous Material Structures

Advanced Engineering Materials, EarlyView.
A numerical model resulting from irreversible thermodynamics for describing transport processes is introduced, focusing on thermodynamic activity gradients as the actual driving force for diffusion. Implemented in CUDA C++ and using CalPhaD methods for determining the necessary activity data, the model accurately simulates interdiffusion in aluminum ...
Ulrich Holländer, Leonhard Holländer, André Langohr, Hans Jürgen Maier   +3 more
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

A Topology Optimization Framework for the Inverse Design of Nonlinear Mechanical Metamaterials

Advanced Engineering Materials, EarlyView.
This work uses topology optimization to design unit cells for mechanical metamaterials with a prescribed nonlinear stress–strain response. The framework adds contact and postbuckling modeling to synthesize microstructures for three highly nonlinear responses, including pseudoductile behavior, monostable with snap‐through buckling, and bistable ...
Charlie Aveline, Matthew Santer, Robert Hewson   +2 more
wiley   +1 more source

3D Malfatti's constrained optimization problem

Journal of Institute of Mathematics and Digital Technology
In 1803, the Italian mathematician Malfatti posed a problem of packing three non-overlapping circles of maximum total area within a given triangle. Malfatti initially believed that the optimal solution involved three circles inscribed within the triangle, each tangent to the other two and touching two sides of the triangle.
Iderbayar Shiilegbat, Enkhbat Rentsen
openaire   +1 more source

Analyzing Electronic Excitations and Exciton Binding Energies in Y6 Films

Advanced Functional Materials, EarlyView.
The Y6 molecule is used for increasing the efficiency of organic solar cells. The exciton binding energy is calculated for ensembles of Y6 molecules that are representative of the typically used films. The calculations show that the excitons typically spread out over many molecules.
Sahar Javaid Akram, Sophie Meißner, Stephan Kümmel   +2 more
wiley   +1 more source

External Anatomical Shapes Reconstruction from Turntable Image Sequences using a Single off-the-shelf Camera

ELCVIA Electronic Letters on Computer Vision and Image Analysis, 2008
Three-dimensional (3D) human body reconstruction and modeling from two-dimensional (2D) images is a topic of great interest and research but still remains a difficult problem to solve.
Teresa Azevedo, João Manuel R. S. Tavares, Mário A. P. Vaz   +2 more
doaj   +1 more source

3D (Bio) Printing Combined Fiber Fabrication Methods for Tissue Engineering Applications: Possibilities and Limitations

Advanced Functional Materials, EarlyView.
Biofabrication aims at providing innovative technologies and tools for the fabrication of tissue‐like constructs for tissue engineering and regenerative medicine applications. By integrating multiple biofabrication technologies, such as 3D (bio) printing with fiber fabrication methods, it would be more realistic to reconstruct native tissue's ...
Waseem Kitana, Indra Apsite, Leonid Ionov   +2 more
wiley   +1 more source

PEMODELAN OBYEK TIGA DIMENSI DARI GAMBAR SINTETIS DUA DIMENSI DENGAN PENDEKATAN VOLUMETRIC

Jurnal Informatika, 2005
In this paper, we implemented 3D object modeling from 2D input images. Modeling is performed by using volumetric reconstruction approaches by using volumetric reconstruction approaches, the 3D space is tesselated into discrete volumes called voxels.
Rudy Adipranata, Liliana liliana
doaj