Parameter Identification for Ultrasound Shear Wave Elastography Simulation
Current Directions in Biomedical Engineering, 2021 Elasticity of soft tissue is a valuable information to physicians in treatment and diagnosis of diseases. The elastic properties of tissue can be estimated with ultrasound (US) shear wave imaging (SWEI).
Neidhardt M. +3 more
doaj +1 more source
A Parametric Study on the Progressive Collapse Potential of Steel Buildings under Truck Collision [PDF]
Journal of Rehabilitation in Civil Engineering, 2017 In this paper, the initiation and propagation of structural damage in a building due to the truck collision to one of its corner columns were investigated.
Vahid Broujerdian, Mehran Torabi
doaj +1 more source
On the ABAQUS FEA Model of Finite Viscoelasticity [PDF]
Rubber Chemistry and Technology, 2009 Abstract Predictions of the QLV (Quasi-Linear Viscoelastic) constitutive law are compared with those of the ABAQUS viscoelastic model for two simple motions in order to highlight, in particular, their very different dissipation rates and certain shortcomings of the ABAQUS model.
CIAMBELLA, JACOPO +2 more
openaire +4 more sources
Bearing Capacity Evaluation of Shallow Foundations on Stabilized Layered Soil using ABAQUS
Studia Geotechnica et Mechanica, 2022 In this paper, the finite element method (FEM) is applied to calculate the bearing capacity of two footings having the aspect ratio L/B (where L and B are the length and width of the footing, respectively) equal to 1, 2 resting on one-layer and two-layer
Bhardwaj Avinash, Sharma Ravi Kumar
doaj +1 more source
Impact of Tamper Shape on the Efficiency and Vibrations Induced During Dynamic Compaction of Dry Sands by 3D Finite Element Modeling [PDF]
Civil Engineering Infrastructures Journal, 2017 Dynamic compaction is a soil improvement method which has been widely used for the increase of bearing capacity through stress wave propagation during heavy tamping. The cost and time of project implementation can be effectively curtailed by developing a
Sahar Mehdipour, Amir Hamidi
doaj +1 more source
Optimal placement of smart sensors for RCC dams structural health monitoring using Monte- Carlo [PDF]
مهندسی منابع آب, 2020 Building RCC dams involves pouring and compacting concrete in small layers (30 cm), one on top of another, creating a joint between each layer. This joint could potentially become the “ideal” joint depending on the temperature and lag time between each ...
Ali Shamsai +2 more
doaj
Civil and Environmental Engineering, 2022 This paper investigates the load capacity and failure modes of slender hollow RC column under axial and eccentric loads. For the slender hollow columns, different load eccentricities and hole shapes are used. The finite element software ABAQUS is used to
Braidi Wameedh Issa +1 more
doaj +1 more source
Numerical Investigation of Temperature Effect on Interface Strength in Energy Piles [PDF]
مهندسی عمران شریف, 2021 Due to the growth of energy consumption, air pollution and global warming in the world, the use of renewable energy has become popular in the world due to its variety of resources, lower economic cost and environmental compatibility. One of the unlimited
B. Asadi +2 more
doaj +1 more source
Behaviors of Pipe-Soil Interaction on Unstable Slopes by Finite Element Simulation
Jurnal Teknik Sipil, 2018 Pipe-soil interaction plays an important role to the pipe stress analysis subjected to soil movement due to slope instability and/or slope failure. As the soils / slopes begin to fail, a single pipe or a group of pipes buried inside failure zone will ...
Endra Susila, Fico Agrensa
doaj +1 more source
Nonlinear Dynamic Behavior of Three-Dimensional Moment Steel Frames and Dual System under Vehicle Impact [PDF]
پژوهشهای زیرساختهای عمرانی, 2022 In this study, the potential of progressive collapse of a four-story steel structure due to the collision of an 8-ton truck with the ground floor columns was investigated.
Fateme Safari Honar +3 more
doaj +1 more source