Results 151 to 160 of about 112,410 (304)
Advanced Engineering Materials, EarlyView.This study examines how helicoidal architectures with different porosities respond to bending. Adjusting layer angle and spacing in 3D‐printed polymers reveals clear tradeoffs between stiffness, strength, and energy absorption. Experiments and simulations highlight designs that distribute stress effectively, offering pathways for optimizing lightweight
Praveenkumar Subhash Patil +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Mass density governs the protective behavior of oxide layers on nuclear fuel cladding. Ptychographic X‐ray computed tomography measures zirconium oxide grown on Zircaloy‐4 under reactor and autoclave conditions, revealing nearly identical bulk densities of 5.1 ± 0.80 g cm−3.
Okan Yetik +9 more
wiley +1 more source
Ho:CaF2 Solid-state Saturable-absorber Q switch for the 2-μm Tm,Cr:Y3Al5O12 Laser
, 2012 [[abstract]]The holmium-doped calcium fluoride 1Ho:CaF22 crystal was shown to be an effective solid-state saturable-absorber Q-switch for a flash-lamp-pumped Tm,Cr:Y3Al5O12 laser at 2.017 μm.
Kuo, Yen-Kuang; Birnbaum, Milton; Unlu, Ferruh; Huang, Man-Fang
core
Thermally Tunable Ultra-Broadband Terahertz Metasurface Absorber Based on VO<sub>2</sub> Phase Transition. [PDF]
Nanomaterials (Basel)Ali A +5 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi +3 more
wiley +1 more source
AI-EXAFS: Physics-Informed Prediction of EXAFS from Atomic Structure. [PDF]
Adv Sci (Weinh)Heras-Domingo J +6 more
europepmc +1 more source
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Impact Vibration Absorber of Pendulum Type
In this paper the impact vibration absorber of pendulum type is examined using numerical simulation. Pendulum vibration absorbers are widely used in practice. It consists of pendulum impact mass with motion limiting stops attached to the vibrating system.
Sokolova, Svetlana +2 more
core
Photon cascade engineering in AgCdF<sub>3</sub>/Cu<sub>2</sub>GeSiS<sub>4</sub> dual-absorber solar cells: from spectral complementarity to device excellence. [PDF]
RSC AdvHossain MF +6 more
europepmc +1 more source
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source