Results 91 to 100 of about 225,702 (253)

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Recycling of NiTi Shape Memory Alloys: Fundamental and Technological Aspects of a Vacuum Induction Melting Processing Route

Advanced Engineering Materials, EarlyView.
The present study investigates recycling of NiTi shape memory alloys via vacuum induction melting. An ingot was synthesized from elemental Ni and Ti and subjected to three subsequent remelting cycles. Remelting increases process durations and impurity levels and adversely affects microstructures and functional properties.
Sakia Sophia Noorzayee, Son Tung Mai, Sarath Menon, Braulio Gadiel Sánchez Ortega, Ralf Drautz, Alexander Kauffmann, Gunther Eggeler, Jan Frenzel   +7 more
wiley   +1 more source

Quantitative and qualitative study of airborne radioactive particles in the safety chamber of Tehran Research Reactor

Salāmat-i kār-i Īrān, 2013
Background and Aims : Many systems and processes can cause the introduction of radioactivity into the environment. Human activities in nuclear industry such as nuclear fuel cycle and reactor operation, lead to a significant production and release of ...
R yarahmadi, G.R Moradi, asghar sadighzadeh, B Rezaeifard, ali asghar farshad, shahnaz bakand, bahram salimi   +6 more
doaj  

Magma mass increase under Sakurajima Volcano, Japan, inferred from campaign relative gravity and leveling data from 1975 to 1992: an interpretation from volcanic gas studies

Earth, Planets and Space
Temporal variations of volume and mass in the magma chambers of Sakurajima Volcano were modeled using leveling and relative gravity data collected around the volcano during the eruptive period from 1975 to 1992, to reveal a physical mechanism for the ...
Ryo Oyanagi, Takahito Kazama, Ryunosuke Kazahaya, Isoji Miyagi, Keigo Yamamoto, Masato Iguchi   +5 more
doaj   +1 more source

Correction of the radon exhalation rate using the Kalman filtering to reduce measurement errors

Nuclear Engineering and Technology
The RAD7 detector is widely used for measuring the radon exhalation rate from the surfaces of media such as soil, rocks, and building materials. However, during the measurement process, the accuracy of the results is prone to interference due to the ...
Haoyu You, Jianfeng Tang, Zhongkai Fan, Ruomei Xie, Hongzhi Yuan, Yanliang Tan   +5 more
doaj   +1 more source

Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid

Advanced Engineering Materials, EarlyView.
A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao, Keldy Mason, Mert Gülçür, Rachel Paddock‐Lamb, Prince Alvin Fofanah, Zachariah A. Page, Michael Cullinan   +6 more
wiley   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

Additive Manufacturing of Alumina‐Reinforced Elastomers

Advanced Engineering Materials, EarlyView.
Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani, Zongwen Fu, Robert Göstl, Hamed Shokri, Carmine Putignano, Gianluca Percoco, Bilal Gökce   +6 more
wiley   +1 more source

Quantitative and qualitative evaluation of residual deposits in implanted intravenous ports informs maintenance strategies

Scientific Reports
This study aimed to evaluate the distribution and composition of intraluminal deposits in implanted intravenous ports removed from oncology patients, with a focus on assessing the effectiveness of current nursing maintenance protocols.
Jui-Ying Fu, Yen Chu, Elsie Khai-Woon Toh, Ya-Ying Hsu, Ching-Feng Wu, Po-Chun Chang, Ching-Yang Wu   +6 more
doaj   +1 more source