Results 221 to 230 of about 667 (249)
Some of the next articles are maybe not open access.
Accumulative roll bonding (ARB) and Cross accumulative roll bonding (CARB) in aluminum: A review
Materials Science and TechnologySevere plastic deformation of metals has been employed to achieve significant grain refinement and consequent strengthening of materials. Prominent techniques in this domain are Accumulative Roll Bonding (ARB) and Cross Accumulative Roll Bonding (CARB), which is a variation of the ARB process.
Adriano A. Trajano +3 more
openaire +1 more source
ACCUMULATIVE ROLL BONDING OF AZ31 MAGNESIUM ALLOY
International Journal of Modern Physics B, 2008This work conducted to investigate the effects of accumulative roll bonding (ARB) method on achieving the ultra-fine grain microstructure in AZ31 alloy. Accordingly, a number of ARB routes at 400°C, applying thickness reductions per pass of 35%, 55%, and 85% were performed.
S. M. FATEMI-VARZANEH +2 more
openaire +1 more source
Accumulative Roll Bonding of 7075 Aluminium Alloy at High Temperature
Materials Science Forum, 2010The 7075 Al alloy was processed by accumulative roll bonding (ARB) at 300, 350 and 400 °C. The microstructure and texture were characterized and the hardness was measured. Cell/(sub)grain sizes less than 500 nm and typical β-fibre rolling texture were observed in the three ARBed samples.
Hidalgo, P. +3 more
openaire +3 more sources
Annealing Behavior of Accumulative Roll Bonding Processed Aluminum Composites
steel research international, 2013Accumulative roll bonding (ARB) is an effective method to produce ultrafine‐grained (UFG) sheet materials with high strength. In this work, the ARB process up to five cycles was performed to the starting materials AA1050 and AA6061 and produced three different laminates: AA1050/AA1050, AA6061/AA6061, and AA1050/AA6061.
Su, Lihong +3 more
openaire +4 more sources
Manufacturing and Mechanical Behavior of Titanium-Steel Composite by Accumulative Roll Bonding
Key Engineering Materials, 2021Metal matrix composites have attracted interest for use in several engineering applications and this study focuses on the fabrication titanium and interstitial free steel composite and its mechanical performance. Accumulative roll bonding (ARB) was employed as a severe plastic deformation method to fabricate the multi-layered composite up to three ...
Tahir, Furqan, Yapıcı, Güney Güven
openaire +1 more source
Nanotwins Formation in Accumulative Roll-Bonded Brass
2017Accumulative roll-bonding (ARB) is a severe plastic deformation process that is using rolling to produce ultrafine grains in coarse grained metallic materials. In this study, ARB has been applied on 70/30 brass up to 6 cycles at ambient temperature and non-lubricated conditions to apply a true strain up to 4.8 Von Mises strain. Microstructures of ARBed
Pasebani, S. +2 more
openaire +1 more source
Bond Strength of Ultrafine Grained Zr Fabricated by Accumulative Roll Bonding
Materials Science Forum, 2008The bond strength of ultrafine grained Zr with a grain size of 0.4 µm, fabricated by accumulative roll bonding (ARB), was assessed. The shear strength of the bond was estimated to be about 20% of the shear fracture strength of the as processed metal, a ratio significantly higher than that found in other materials processed by similar methods.
Jiang, L. +3 more
openaire +2 more sources
Accumulative Roll Bonding of AA8006, AA8011 and AA5754 Sheets
Materials Science Forum, 2006Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation, which involves multiple repetitions of surface treatment, stacking, rolling, and cutting. The rolling with 50% reduction in thickness bonds the sheets. After several cycles, ultrafine-grained (UFG) materials are produced.
Margarita Slámová +6 more
openaire +1 more source
Hardness measurements of accumulative roll-bonded Mo foils
Journal of Materials Science, 2010The hardness of accumulative roll bonding (ARB)-processed multilayers has been measured in the past with microindentation studies. In some cases the lateral indent size of microindenters, however, is too large. For example, if multilayers are ARB-processed that consist of arrays of different elemental foils the hardness ratio of the layers has been ...
G. Marathe, R. J. Hebert
openaire +1 more source
Processing a Multilayer laminate sheet by accumulative roll bonding
International Journal of Applied Science and Engineering Research, 2013In this work, AA7075/AA1100 multilayer sheet has been processed by accumulative roll-bonding to a large strain followed by a T6 heat treatment. The rolling work was done at the solution temperature of AA7075. The strength, microhardness and ductility of the ARB sheet have been increased. The microstructure had a UFG structure with average grain size of
Kawunga Nyirenda, Liu Qing, Chen Zejun
openaire +1 more source