Results 21 to 30 of about 3,709 (249)

Effect of SiC addition on the mechanical properties and wear behavior of Al-SiC nanocomposites produced by accumulative roll bonding

Materials Research Express, 2020
In this study, we manufactured Al and Al-SiC nanocomposites (SiC vol.% = 1, 2 and 4) using accumulative roll bonding (ARB) at room temperature. Mechanical and wear characteristic of the manufactured samples was studied.
Wael S Hassanein, A M Sadoun, A Abu-Oqail   +2 more
doaj   +1 more source

Microstructure and Mechanical Properties of the Ni/Ti/Nb Multilayer Composite Manufactured by Accumulative Pack-Roll Bonding

Metals, 2020
In this work, accumulative pack-roll bonding successfully manufactured the Ni/Ti/Nb multilayer composite. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by ...
Nan Ye, Xueping Ren, Juhua Liang
doaj   +1 more source

Hard Copper with Good Electrical Conductivity Fabricated by Accumulative Roll-Bonding to Ultrahigh Strains

Metals, 2016
By modifying the accumulative roll-bonding (ARB) procedures, accumulative roll-bonding (ARB) processing up to 30 cycles (N) with a 50% thickness reduction per cycle (equivalent strain = 24) at room temperature was conducted on pure copper.
Gongcheng Yao, Qingsong Mei, Juying Li, Congling Li, Ye Ma, Feng Chen, Guodong Zhang, Bing Yang   +7 more
doaj   +1 more source

Optimization of the accumulative roll bonding process parameters and SiC content for optimum enhancement in mechanical properties of Al-Ni-SiC composites

Alexandria Engineering Journal, 2023
Accumulative Roll Bonding (ARB) is one of the main techniques to manufacture nanocomposites, however, due to the large number of parameters that control this process, its application is relatively expensive.
Waheed S. Barakat, M. Kh. Younis, A.M. Sadoun, A. Fathy, Mohamed I.A. Habba   +4 more
doaj   +1 more source

Formability of the 5754-aluminum alloy deformed by a modified repetitive corrugation and straightening process [PDF]

, 2020
Sheets of 5754-aluminum alloy processed by a modified repetitive corrugation and straightening (RCS) process were tested in order to measure their formability. For this purpose, forming limit curves were derived.
Alfonso, Ismeli, Cabrera Marrero, José M., Elizalde Huitrón, Sergio Alberto, Ezequiel Alvarado, Marco Alejandro, Figueroa, I. A., González, Gonzalo, Picas Barrachina, Josep Anton   +6 more
core   +2 more sources

Simulation of the Accumulative Roll-Bonding process through warm torsion test

Journal of Materials Research and Technology, 2018
The objective of this work was simulating the process of severe plastic deformation, specifically the Accumulative Roll-Bonding process (ARB) in low carbon steel, by warm torsion test, using the typical ARB process parameters.
Lumena Glória de Souza Nunes, Marcelo Lucas Pereira Machado   +1 more
doaj   +1 more source

Bonding of similar AA3105 aluminum alloy by accumulative roll bonding process [PDF]

, 2021
Accumulative roll-bonding (ARB) is a novel plastic straining process aimed at bonding of similar and dissimilar metal combinations. Moreover, it is used recently to produce ultrafine grain materials and metal matrix reinforced composites to enhance ...
Almehtedi R., Aymerich F., Buonadonna P., Carta Mauro, El Mehtedi M., Lai D.   +5 more
core   +1 more source

The Effect of Asymmetry on Strain Distribution, Microstructure and Texture of Multilayer Aluminum Composites Formed by Roll-Bonding

Frontiers in Materials, 2020
AA1050/AA7050 multilayered composite sheets with a proportion of 1:1 were produced by Accumulative Roll Bonding (ARB) and Asymmetric Accumulative Roll-Bonding (AARB), using up to 8 cycles and intermediate annealing treatments at 500°C.
D. C. C. Magalhães, J. B. Rubert, O. M. Cintho, V. L. Sordi, A. M. Kliauga   +4 more
doaj   +1 more source

Microstructure, Mechanical and Thermal Properties of Al/Cu/SiC Laminated Composites, Fabricated by the ARB and CARB Processes

Crystals, 2023
The aim of the current work is to investigate the effect of SiC particle weight percent and rolling passes on Al/Cu/SiC laminated composites, fabricated by accumulative roll-bonding (ARB) and cross-accumulative roll-bonding (CARB) processes.
Jie Luo, Rashid Khattinejad, Amirhossein Assari, Moslem Tayyebi, Bejan Hamawandi   +4 more
doaj   +1 more source

The evolution of the structure and mechanical properties of aluminum during accumulative roll bonding [PDF]

, 2017
The dependence of microstructure, microhardness, and strength properties in tensile strain tests of commercially pure aluminum on strain during accumulative roll-bonding was studied.
Ivanov, K. V., Kudryavtsev, E. V.
core   +1 more source