Results 31 to 40 of about 878 (207)
Fabrication of AA1060/Al2O3 Composites by Warm Accumulative Roll Bonding Process and Investigation of its Mechanical Properties and Microstructural Evolution [PDF]
International Journal of Advanced Design and Manufacturing Technology, 2017 Recently accumulative roll bonding (ARB) has been used as a novel method to produce particle reinforced metal matrix composites. The accumulative roll bonding as a severe plastic deformation (SPD) rolling procedure aimed at enhancing the mechanical ...
M. Heydari Vini, P. Farhadipour
doaj
Journal of Materials Research and Technology, 2023 A Cu matrix composite was designed and produced successfully by adding carbon nanotubes (CNTs) as reinforcement particles. The accumulative roll bonding (ARB) process was used to introduce the material in the shape of the sheet.
Bahram Rahnama Falavarjani +2 more
doaj +1 more source
Ultra-fine grained bulk steel produced by accumulative roll-bonding (ARB) process [PDF]
Scripta Materialia, 1999 Much attention has been directed recently to ultra-grain refining of metallic materials, where the grain size is reduced to less than 1 {micro}m. It is expected that submicrometer grained structure would result in high strength and toughness at ambient temperature as well as high strain rate or low temperature superplasticity at elevated temperatures ...
N Tsuji +3 more
openaire +1 more source
Crystals, 2019 In this report, reverse accumulative roll-bonding (ARB) was conducted for the first time. It was found that the microstructure after reverse ARB was relatively coarser than that after unidirectional ARB, and texture intensity was slightly weaker.
Hui Wang, Cheng Lu, Kiet Tieu
doaj +1 more source
Enhancement of mechanical properties for Mg-9Li-1Zn alloy by accumulative roll bonding
Materials Research Express, 2020 The microstructures and mechanical properties of LZ91 alloys by accumulative roll bonding (ARB) were firstly investigated. The results show that the cycle numbers of ARB process and preheating temperatures before ARB process have an impact on the ...
Akhmad Saufan +2 more
doaj +1 more source
Structural characteristics of Cu/Ti bimetal composite produced by accumulative roll-bonding (ARB)
Materials & Design, 2017 Abstract Cu/Ti nanostructured bimetal composite was produced by accumulative roll-bonding (ARB) technique and the structural characteristics of this composite were studied both experimentally and by finite element analysis. Macrostructure evolution of the composite layers was investigated by optical and scanning electron microscopes.
M. Hosseini +4 more
openaire +1 more source
Report of International NanoSPD Steering Committee and statistics on recent NanoSPD activities
, 2014 The Université de Lorraine in Metz, France, is the selected site for the 6th International Conference on Nanomaterials by Severe Plastic Deformation (NanoSPD6) following a series of five earlier conferences.
Valiev, R.Z., Langdon, T.G.
core +1 more source
Metals, 2021 A severe plastic deformation process, termed accumulative extrusion bonding (AEB), is conceived to steady-state bond metals in the form of multilayered tubes. It is shown that AEB can facilitate bonding of metals in their solid-state, like the process of
Matthew R. Standley, Marko Knezevic
doaj +1 more source
Mechanical Properties and Microstructural Evolution of AA5083/Al2O3 Composites Fabricated by Warm Accumulative Roll Bonding [PDF]
International Journal of Advanced Design and Manufacturing Technology, 2016 In this study, warm accumulative roll bonding (Warm- ARB) process has been used to produce Metal Matrix Composite (MMC: AA5083/-5% Al2O3). Starting materials were roll bonded as alternate layers up to 5 rolling cycles with 300°C preheating for five ...
Mohammad Heydari Vini +2 more
doaj
MATERIALS TRANSACTIONS, 2003 The differential speed accumulative roll bonding (DSARB) process was attempted to strengthen 1100 aluminum sheet via grain refinement. The roll peripheral speed of one roll was 2.0 m/min and that of another roll was 3.6 m/min. The roll speed ratio was kept at 1.8. The accumulative roll bonding was conducted up to 6 cycles at ambient temperature without
Lee, Seong-Hee +2 more
openaire +2 more sources