Results 121 to 130 of about 342,937 (270)

Multilayer Self‐Limiting Electrospray Deposition via Stepped Voltage Bias

Advanced Engineering Materials, EarlyView.
Self‐limiting electrospray deposition (SLED) uses a high voltage to generate and deposit a charged payload on a target surface. The coating retains its charge, repelling newly arriving material. SLED thickness can be decreased by applying a secondary bias to the target.
Madhuri Deb, S. Rahman Pejman, Alexander Jakimowicz, Jonathan P. Singer   +3 more
wiley   +1 more source

The Influence of Field‐Assisted Sintering Technology (FAST) Temperature and Cooling Rate on the Microstructural Evolution in Gamma‐Titanium Aluminide Alloy GE4822

Advanced Engineering Materials, EarlyView.
Controlling the Field Assisted Sintering Technology (FAST) parameters, dwell temperature and cooling rate, significantly influences the microstructural evolution in titanium aluminide GE4822. Significant γ‐lamellar colonies develop only upon cooling through the α‐transus.
Jack Krohn, James Pepper, Martin Jackson
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

A performance comparison between two design techniques for non-linear output feedback control

, 2004
For a system possessing a non-linear output feedback normal form, an observer backstepping design is compared to a high gain observer design with respect to non-singular performance cost functional.
French, M, Xie, C
core   +1 more source

Adaptive Stabilization Without High-Gain

, 1986
During the last few years there has been a very intense discussion on the applicability of adaptive control and on ‘standard assumptions’ made in the traditional theory.
Mårtensson, Bengt, Lund University.
core  

Architecture‐Driven Sensor Stability in Weft‐Knitted Engineering Textiles

Advanced Engineering Materials, EarlyView.
Textile‐integrated sensor architectures are systematically compared to evaluate their electromechanical behavior under combined mechanical and environmental loading. Pocket‐based integration exhibits stable and reproducible signals, whereas tunnel‐based routing shows higher sensitivity accompanied by increased variability.
Adnan Maroof Khan, Johannes Wendler, Dilbar Aibibu, Johannes Mersch, Michael Wöltje, Chokri Cherif   +5 more
wiley   +1 more source

Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials

Advanced Engineering Materials, EarlyView.
Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley   +1 more source

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Materials‐Driven Additive Manufacturing for Electrical Machines: Qualification‐Oriented Design Beyond Geometric Freedom

Advanced Engineering Materials, EarlyView.
This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley   +1 more source

All‐in‐One Analog AI Hardware: On‐Chip Training and Inference with Conductive‐Metal‐Oxide/HfOx ReRAM Devices

Advanced Functional Materials, EarlyView.
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone, Victoria Clerico, Wooseok Choi, Tommaso Stecconi, Folkert Horst, Laura Bégon‐Lours, Matteo Galetta, Antonio La Porta, Nikhil Garg, Fabien Alibart, Bert Jan Offrein, Valeria Bragaglia   +11 more
wiley   +1 more source