Results 11 to 20 of about 545 (179)
Machinability Evaluation in Hard Milling of AISI D2 Steel [PDF]
Materials Research, 2016 Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools.
Vinayak Neelakanth Gaitonde +4 more
doaj +5 more sources
Surface Integrity in the Grinding of Hardened AISI D2 Steel. [PDF]
Materials (Basel)The surface integrity of grinding has a significant influence on the service performance and life of machined parts. In this study, the influence of grinding parameters and the grit size of the grinding wheel on the surface integrity of the hardened steel, including the roughness, microstructure, and hardness of the subsurface and the residual stress ...
Zhang T +8 more
europepmc +3 more sources
Wear and corrosion interaction of AISI D2 in an acidic environment
Tribologia - Finnish Journal of Tribology, 2021 The tribological, electrochemical and tribo-electrochemical behavior of bare AISI D2 was studied. The tribological aspects were tested by pin on disc with an aluminum oxide ball as counter body, the electrochemical tests were performed in an aqueous solution of citric acid and the tribo-electrochemical evaluation was through a combination of both tests.
Garcia Ramos, Tania +3 more
openaire +3 more sources
Characterization and Diffusion Kinetics of Silicon on AISI D2 Steel
Silicon, 2023 This paper presents the simultaneous influence of two different activators (NH4Cl and NaF) on the kinetic evolution during siliconising of steel. The AISI D2 tool steel surface was coated by pack siliconising through the growing of silicon on the surface. Pack siliconising was accomplished by employing a mixture of powders of Si 12 wt% + NH4Cl 0.5 wt% +
Najafizadeh, Mojtaba +5 more
openaire +2 more sources
MATEC Web of Conferences, 2018 Cylindrical grinding is the process of metal removal using multiple cutting point. The objective of the study is to investigate the chip characteristics (shape and width) and surface roughness materials. The materials are AISI 1020, AISI 1045, AISI 1090,
Isti Nugroho Wahyu +2 more
doaj +1 more source
Pack Siliconizing Optimization of AISI D2 Tool Steel
Silicon, 2022 AbstractThe paper describes the pack siliconizing optimization procedure for AISI D2 tool steel. Pack siliconizing was performed by employing different treating temperatures (falling in the range 650–950 °C) and times (falling in the range 2–4 h). The siliconizing atmosphere was obtained through silicon (at 12 wt.%) with the addition of different ...
Mojtaba Najafizadeh +4 more
openaire +2 more sources
Study on Thixojoining Process Using Partial Remelting Method
Advances in Materials Science and Engineering, 2013 Cold-work tool steel is considered to be a nonweldable metal due to its high percentage content of carbon and alloy elements. The application of a new process of the semisolid joining of two dissimilar metals is proposed. AISI D2 cold-work tool steel was
M. N. Mohammed +3 more
doaj +1 more source
Düzce Üniversitesi Bilim ve Teknoloji Dergisi, 2015 Yüzey kalitesi, birbiriyle etkileşim içinde olan makina ekipmanlarının çalışma verimini ve ömrünü önemli derecede etkilemektedir. Kesici takım, işlenen malzeme, kesme parametreleri gibi yüzey pürüzlülüğünü etkileyen birçok parametre vardır.
Emine Şirin +3 more
doaj +4 more sources
Experimental Analysis on Multilayer Cladding Using AISI-M4/H13 Metal Powders for Enhancement of Wear Resistance and Shockproof Characteristics [PDF]
한국정밀공학회지, 2019 Generally, press molds have thermal and mechanical impact wear during usage. To improve the life of the mold, enhancement of mechanical properties such as abrasion resistance and shockproof capability is required.
Yeong Kwan Jo +5 more
doaj +1 more source
Microstructure and Mechanical Properties of High-Strength Tool Steels [PDF]
Archives of Metallurgy and MaterialsIn this study, high-strength tool steel specimens based on AISI D2 with a C content of 1.6% or more were developed by adjusting alloying elements (C, Cr, Mo, and V).
Hong-Gu Lee +5 more
doaj +1 more source