Results 21 to 30 of about 141,194 (208)

Microstructural and Mechanical Characterization of Ledeburitic AISI D2 Cold-Work Tool Steel in Semisolid Zones via Direct Partial Remelting Process

open access: yesJournal of Manufacturing and Materials Processing, 2022
The success of the thixoforming process largely depends on the created microstructure, which must be globular in the liquid phase. The solid–liquid structural changes that occur on as-annealed D2 tool steel when it is subjected to the so-called DPRM are ...
M. N. Mohammed   +7 more
doaj   +1 more source

MITIGATION OF AGRICULTURAL ENERGY REQUIREMENT IN BANGLADESH USING MICROALGAE PRODUCTION [PDF]

open access: yesJournal of Mechanical Engineering and Sciences, 2013
A high quality joint between tool steel and stainless steel alloys is hard to achieve with the conventional welding process. In this study, a new process of joining semi-solid AISI D2 tool steel and AISI 304 stainless steel using a partial remelting ...
Mohammad Farzid Hasan   +3 more
doaj   +1 more source

AISI D2 Soğuk İş Takım Çeliğinin Frezelenmesi Üzerine Bir Derleme [PDF]

open access: yes, 2020
Takım çelikleri, kullanım alanları bakımından diğer çelik gruplarına göre endüstriyel uygulamalarda daha yaygın olarak kullanılmaktadır. Takım çelikleri farklı sıcaklıklar altında şekillendirme ve işleme uygulamalarında aşınmaya karşı dayanacak şekilde ...
Şirin, Şenol, Şirin, Emine
core   +2 more sources

The Effect of Current Density and Hard Chrome Coating Duration on the Mechanical and Tribological Properties of AISI D2 Steel

open access: yesJournal of Materials Exploration and Findings, 2023
The effect of hard chromium coating on AISI D2's mechanical properties and wear resistance has been investigated using the electrolysis technique with varying current and coating duration. The variations of current used are 0.8 A, 1.2 A, and 1.6 A, while
Indah Uswatun Hasanah   +2 more
doaj   +1 more source

Characterization and Diffusion Kinetics of Silicon on AISI D2 Steel

open access: yesSilicon, 2023
This paper presents the simultaneous influence of two different activators (NH4Cl and NaF) on the kinetic evolution during siliconising of steel. The AISI D2 tool steel surface was coated by pack siliconising through the growing of silicon on the surface. Pack siliconising was accomplished by employing a mixture of powders of Si 12 wt% + NH4Cl 0.5 wt% +
Najafizadeh, Mojtaba   +5 more
openaire   +2 more sources

Desirability response surface for wear resistance of ball-end milled surface of AISI D2 steel under dry cutting condition.

open access: yes, 2023
Desirability response surface for wear resistance of ball-end milled surface of AISI D2 steel under dry cutting condition.
Guosong Zhang (3210132)   +3 more
core   +1 more source

Heat Treatment of Sintered Valve Seat Inserts [PDF]

open access: yesMaterials Research, 2018
The characterization of sintered valve seat inserts (VSIs) after being subjected to different heat treatment operations has been carried out. The VSIs were obtained from three different alloys by mixing iron powder with AISI M3:2, AISI M2 high-speed ...
Maurilio Pereira Gomes   +7 more
doaj   +1 more source

Pack Siliconizing Optimization of AISI D2 Tool Steel

open access: yesSilicon, 2022
AbstractThe paper describes the pack siliconizing optimization procedure for AISI D2 tool steel. Pack siliconizing was performed by employing different treating temperatures (falling in the range 650–950 °C) and times (falling in the range 2–4 h). The siliconizing atmosphere was obtained through silicon (at 12 wt.%) with the addition of different ...
Mojtaba Najafizadeh   +4 more
openaire   +2 more sources

A Novel Methods for Fracture Toughness Evaluation of Tool Steels with Post-Tempering Cryogenic Treatment

open access: yesMetals, 2017
Cryogenic treatments are usually carried out immediately after quenching, but their use can be extended to post tempering in order to improve their fracture toughness.
Ramona Sola   +3 more
doaj   +1 more source

Characterization chip formation of commercial steel materials at low speed cylindrical grinding processes

open access: yesMATEC Web of Conferences, 2018
Cylindrical grinding is the process of metal removal using multiple cutting point. The objective of the study is to investigate the chip characteristics (shape and width) and surface roughness materials. The materials are AISI 1020, AISI 1045, AISI 1090,
Isti Nugroho Wahyu   +2 more
doaj   +1 more source

Home - About - Disclaimer - Privacy