Results 171 to 180 of about 1,120,503 (214)
Some of the next articles are maybe not open access.

Prediction of Machining Performances in Hardened AISI D2 Steel

Materials Today: Proceedings, 2019
Abstract The current research focuses on predicting the surface roughness, the flank wear and (chip–tool) interface temperature when turning the hardened AISI D2 (55 ± 1 HRC) employing a mixed ceramic (Al2O3 + TiCN) tool in dry condition. Quadratic regression methodology has been introduced and their performances are compared on basis of mean error ...
Ramanuj Kumar   +5 more
openaire   +1 more source

Surface Topography in Machining of AISI D2 Hardened Steel

Applied Mechanics and Materials, 2013
Surface topography plays an important part in understanding the nature of machined surfaces. This study is focused on surface topography of AISI D2 hardened steel (58-62 HRC) under dry milling process. Roughness, surface morphology and defects analysis were investigated.
N.A.H. Jasni, Mohd Amri Lajis
openaire   +1 more source

Electrochemical boriding and characterization of AISI D2 tool steel

Thin Solid Films, 2011
Abstract D2 is an air-hardening tool steel and due to its high chromium content provides very good protection against wear and oxidation, especially at elevated temperatures. Boriding of D2 steel can further enhance its surface mechanical and tribological properties.
Sista, V.   +4 more
openaire   +2 more sources

Experimental Study in HSM of Hardened Steel AISI D2

Advanced Materials Research, 2009
Hardened steel is widely used for good mechanical property, but its machinability is bad comparatively. It is efficient to enhance metal removed rate when high speed milling (HSM) hardened steel, but tool wear is rapid. In this paper, high-speed milling experiments were carried out for hardened steel with TiAlN coated tools.
B.Y. Qi, Ning He, Liang Li
openaire   +1 more source

Micro-Milling of Hardened AISI D2 Tool Steel

Advanced Materials Research, 2012
The paper presents an experimental investigation into the slotting of hardened AISI D2 (~62HRC) tool steel using 0.5mm diameter coated (TiAlN) tungsten carbide (WC) end mills. SEM analysis of tool morphology and coating integrity was undertaken on all tools prior to testing.
J.B. Saedon   +3 more
openaire   +1 more source

Performance characteristics of hardened AISI D2 steel turning: A review

Materials Today: Proceedings, 2020
Abstract Hard turning is the process of machining hardened steels that have above 45HRC. In metal-manufacturing, hard turning potentially substitutes the grinding process as it possesses lots of benefits like higher metal volume removal rate, less costly, easy to handle, flexible tooling and exhibiting closer surface quality to grinding finish.
Rajashree Mallick   +3 more
openaire   +1 more source

Corrosion Behavior of TiN Coated AISI D2 Steel

2015
In this study, the corrosion behaviors of nitride and titanium nitride (TiN) layers deposited on AISI D2 steel samples are reported. Steel was at first nitrided in a nitrogen and ammonia atmosphere at 575 °C for 8 h and then titanium nitride coating treatment was performed in the powder mixture consisting of ferro-titanium, ammonium chloride and ...
ÇEĞİL, Özkan, ŞEN, Şaduman
openaire   +2 more sources

Microstructural Evolution of AISI D2 Tool Steel during Aging

Solid State Phenomena, 2011
The effects of low temperature isothermal treatments on a quenched AISI D2 tool steel was studied using Barkhausen Noise, X-ray diffraction, dilatometry and optical and electronic microscopy. The specimens were austenitized at 1040°C and quenched in oil.
Paula Fernanda Silva Farina   +5 more
openaire   +1 more source

The characteristics of cutting forces in the micro-milling of AISI D2 steel

Journal of Mechanical Science and Technology, 2009
The interaction effect of parameters to surface topography and cutting forces is investigated, and the magnitudes of these parameters are determined in the micro-milling of AISI D2 steel. The results show that the feed per tooth has a prominent impact on the surface topography.
Cheng-Zhe Jin   +4 more
openaire   +1 more source

Influence of varied cryotreatment on the wear behavior of AISI D2 steel

Wear, 2009
Abstract Exploration of the benefit of cryotreatment for achieving improvement in wear resistance of die/tool steel is a topic of current research interest. A series of wear tests has been carried out on AISI D2 steel samples subjected to cryotreatment at 77 K for different durations.
D. Das, A.K. Dutta, K.K. Ray
openaire   +1 more source

Home - About - Disclaimer - Privacy