Results 61 to 70 of about 121,830 (268)

Research progress and development tendency of ultra-high strength aluminum alloys

Journal of Aeronautical Materials
Ultra-high strength aluminum alloy has achieved extensive application in the nuclear，aerospace，and aviation industries because of its high specific strength and low density. The fifth generation of ultra-high strength aluminum alloy has been produced，and
XING Qingyuan, ZANG Jinxin, CHEN Junzhou, YANG Shoujie, DAI Shenglong   +4 more
doaj   +1 more source

Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control

Advanced Engineering Materials, EarlyView.
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian, Frédéric Demoly, Mohammad Lakhi, Bernard Rolfe, Mahdi Bodaghi   +4 more
wiley   +1 more source

Inca figurines from the Ethnologisches Museum in Berlin: an analytical study of some typical and atypical productions

Bulletin de l'Institut Français d'Études Andines, 2017
Fourteen hollow and one cast anthropomorphic and zoomorphic figurines produced in Incan times for ritual offerings from the Ethnologisches Museum in Berlin were selected to investigate the technologies and alloys used for their fabrication with portable ...
Maria Filomena Guerra, Manuela Fischer, Martin Radtke, Uwe Reinholz   +3 more
doaj   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

An Inca silver figurine at National Museums Scotland: Technological study

Bulletin de l'Institut Français d'Études Andines, 2017
The hollow silver male miniature figurine from National Museums Scotland is one of the tallest specimens made in precious metals attributed to the Incas.
Lore Troalen, Maria Filomena Guerra
doaj   +1 more source

Metastable superconducting alloys. [Amorphous alloys] [PDF]

, 1978
The study of metastable metals and alloys has become one of the principal activities of specialists working in the field of superconducting materials. Metastable crystalline superconductors such as the A15-type materials have been given much attention.
openaire   +2 more sources

Impact of Textile Architecture on the Electromechanical Behavior of Conductive Carbon: Silicone Composite Strain Sensors

Advanced Engineering Materials, EarlyView.
A stretchable carbon composite is integrated by stencil printing onto two different types of textile, with different yarn morphologies. The impact of the knit structure and coating direction on the performance of the sensor composite is evaluated and used to derive a model estimating nominal resistance at a given strain near the percolation threshold ...
Gabriela Ananieva, Giulia Spallanzani, Peter Zalar   +2 more
wiley   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source

Evaluation of the Potential of Laser Shock Peening Compared with Cold Expansion for Improving Fatigue Resistance of Riveted Lap Joints of Aerospace Grade 7175 Al Alloy

Advanced Engineering Materials, EarlyView.
This study investigates laser shock peening for enhancing fatigue performance of riveted aerospace aluminum joints. A comparative approach with cold expansion combines fatigue testing and synchrotron X‐ray methods. Integrating mechanical testing with residual stress and strain characterization provides insights into how different treatments affect the ...
Ogün Baris Tapar, David Osman Busse, Maximilian Sprengel, Domenico Furfari, Marc‐André Nielsen, Guilherme Abreu Faria, Jérémy Epp   +6 more
wiley   +1 more source

Adjustment of Coatings Morphology and Particle Distribution of Layered Silicates by Freeze‐Drying for Improved Gas Barriers

Advanced Engineering Materials, EarlyView.
Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes, Moritz Bätcher, Andrea Deißenberger, Volkmar Stenzel, Andreas Hartwig   +4 more
wiley   +1 more source