Results 51 to 60 of about 746,731 (226)
Thermokinetic Modeling Approach for Aluminide Diffusion Coatings on Molybdenum Substrates
Advanced Engineering Materials, Volume 27, Issue 13, July 2025.The advancement of innovative materials for protective coatings in high‐temperature environments relies on a detailed understanding of diffusion processes within these systems. This article presents findings from modeling approaches, supporting the development and optimization of coating materials by focusing on the prediction of diffusion‐driven ...
Jurica Filipovic +4 more
wiley +1 more source
High Temperature Materials and Processes, 2021 Thermal barrier coatings (TBCs) are widely used for protection of gas turbine parts from high temperature and corrosion. In the present study, the new concept of TBCs with three-element-modified aluminide coatings was presented.
Góral Marek +5 more
doaj +1 more source
Advanced Engineering Materials, Volume 27, Issue 7, April 2025.This study investigates the effect of a NiAl coating on additively manufactured (AM) IN939 to improve its cyclic oxidation resistance at 1050 °C. The coating promotes protective α‐Al2O3 formation, allowing durability for up to 240 cycles, while uncoated AM‐IN939 experiences spallation and weight loss due to nonprotective oxides.
Fatih Guler +5 more
wiley +1 more source
Advanced Engineering Materials, Volume 27, Issue 3, February 2025.Free‐standing Ni/Al multilayer thin films are investigated with a novel commercial nanocalorimeter and a conventional calorimeter. The Kissinger analysis shows a monotonic Arrhenius behavior over the entire five orders of magnitude of heating rates for all thermal events.
Sascha S. Riegler +12 more
wiley +1 more source
Method of protecting a surface with a silicon-slurry/aluminide coating [PDF]
, 1982 A low cost coating for protecting metallic base system substrates from high temperatures, high gas velocity oxidation, thermal fatigue and hot corrosion is described. The coating is particularly useful for protecting vanes and blades in aircraft and land
Deadmore, D. L., Young, S. G.
core +1 more source
, 2021 In this paper, mechanical properties of the as-received and aluminide layer coated MAR 247 nickel based superalloy were examined through creep and fatigue tests.
M. Kopeć +5 more
semanticscholar +1 more source
RuAl Thin‐Film Deposition by DC Magnetron Sputtering
Advanced Engineering Materials, Volume 27, Issue 3, February 2025.The synthesis and influence of deposition parameters on the corresponding microstructure of single‐phase RuAl in B2 structure is examined via transmission electron microscopy analysis and X‐ray diffraction with additional pole figure measurements. These are correlated to mechanical properties of the magnetron‐sputtered thin films.
Vincent Ott +10 more
wiley +1 more source
Engineering Reports, Volume 6, Issue 12, December 2024.The graphical abstract demonstrates that adding 9 wt% nickel to an Al‐Si matrix composite increases hardness by 25.93%, tensile strength by 40.3%, and density by 6.01%, but decreases impact strength by 50% compared to the A413 alloy. It includes SEM images, a stir casting schematic, and data on tensile and impact behavior.
A. Saiyathibrahim +3 more
wiley +1 more source
Causal discovery to understand hot corrosion
Materials and Corrosion, Volume 75, Issue 12, Page 1639-1651, December 2024.Causal discovery has been applied to a small hot corrosion data set to explore the factors influencing the mechanism. The left part of the picture shows the sequence of the applied methodology, from the data processing to obtaining the relationship between the factors influencing hot corrosion.
Akhil Varghese +4 more
wiley +1 more source
Multi-layered Ruthenium-modified Bond Coats for Thermal Barrier Coatings [PDF]
, 2006 Diffusional approaches for fabrication of multi-layered Ru-modified bond coats for thermal barrier coatings have been developed via low activity chemical vapor deposition and high activity pack aluminization.
A.G. Evans +58 more
core +2 more sources