Control of Magnesium Alloy Corrosion through the Use of Engineered Intermetallics [PDF]
, 2014 The low density and high relative strength of Mg alloys means they can offer engineering benefits over steels or Al alloys. However, the susceptibility of Mg alloys to corrosion has limited their exploitation and restricted their use to more benign ...
Pidcock, Andrew
core +7 more sources
Potential fatigue strength improvement of AA 5083-H111 notched parts by wire brush hammering: Experimental analysis and numerical simulation [PDF]
, 2014 The effects of milling as machining process and a post-machining treatment by wire-brush hammering, on the near surface layer characteristics of AA 5083-H111 were investigated.
SIDHOM, Habib +4 more
core +1 more source
Microstructure and properties of welds between 5754 Al alloys and AZ31 Mg alloys using a Yb:YAG laser [PDF]
, 2014 The authors wish to thank Mr. Henri ANDRZEJEWSKI for his technical assistance in laser experiments. The authors wish to place their sincere thanks to Professor Philippe BOURNOT and Dr.
BANNOUR, Sana +9 more
core +1 more source
The influence of position in overlap joints of Mg and Al alloys on microstructure and hardness of laser welds [PDF]
, 2013 Structure and properties of laser beam welding zone of dissimilar materials, AZ31 magnesium alloy and A5754 Aluminum alloy, are investigated. The microstructure and quality of the Mg/Al weld were studied by metallography, microhardness and optical ...
BANNOUR, Sana +11 more
core +1 more source
Simulating the galvanic coupling between S-Al2CuMg phase particles and the matrix of 2024 aerospace aluminium alloy [PDF]
, 2012 Study of the corrosion behaviour of a magnetron sputtered Al–Cu/Al–Cu–Mg model alloy couple in sulphate solutions has been undertaken to gain insight into the galvanic coupling between the matrix and SAl2CuMg particles in the 2024 aluminium alloy (AA2024)
Blanc, Christine +11 more
core +1 more source
Strain mapping and nanocrystallite size determination by neutron diffraction in an aluminum alloy (AA5083) severely plastically deformed through equal channel angular pressing [PDF]
, 2013 Six specimens of an aluminum alloy (AA-5083) extruded by Equal Channel Angular Pressing following two different routes plus a blank sample were examined with a neutron radiation of 1.5448 Å. Macrostrain maps from the (311) reflection were obtained.
Pérez, C. Luis +3 more
core +1 more source
A predictive fatigue life model for anodized 7050 aluminium alloy [PDF]
, 2013 The objective of this study is to predict fatigue life of anodized 7050 aluminum alloy specimens. In the case of anodized 7050-T7451 alloy, fractographic observations of fatigue tested specimens showed that pickling pits were the predominant sites for ...
Chaussumier, Michel +4 more
core +1 more source
Cailiao gongcheng, 2017 The flow stress behavior of 5083 aluminum alloy was investigated under hot compression deformation at 523-723K,strain rates of 0.01-10s-1 and true strains of 0-0.7 with Gleeble-3800 thermal simulator.
FU Ping +4 more
doaj +1 more source
International Journal of Electrochemical Science, 2020 The corrosion resistance of FSW welded joints of 6mm-thick dissimilar 2A12 and 7075 aviation aluminum alloy was investigated. It was concluded that the 7075 aluminum alloy was more resistant to intergranular corrosion than 2A12 aluminum alloy, and when ...
Defeng Zhang +5 more
doaj +1 more source
Tensile ductility improvement of AlSi9Cu1 alloy by chemical composition optimization [PDF]
China Foundry, 2017 Diesel engines, characterized by higher breakout pressure and compression ratio in comparison with gasoline engines, require particularly elevated tensile properties for their engine parts.
Bing-rong Zhang +2 more
doaj +1 more source