Results 31 to 40 of about 196,057 (315)
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Journal of Materials Research and TechnologyThis study investigates the influence of 1–4 wt% Al additions on the microstructure of a flame-retardant Mg-5Ca-1.5Sm alloy, revealing a distinct threshold effect of Al on grain refinement.
Xuerui Wang +12 more
doaj +1 more source
Effect of Heat Treatment on the In-Plane Anisotropy of As-Rolled 7050 Aluminum Alloy
Metals, 2016 Tensile tests were conducted on both as-quenched and over-aged 7050 aluminum alloy to investigate the effect of heat treatment on the in-plane anisotropy of as-rolled 7050 aluminum alloy.
Huie Hu, Xinyun Wang
doaj +1 more source
Heat treatment study of aluminum casting alloy M45 [PDF]
, 1967 Study determines the heat treatment cycle of aluminum casting alloy M-45 which will increase the strength levels of the alloy while maintaining optimum stress corrosion resistance.
Lovoy, C. V.
core +1 more source
Evaluation on crashworthiness and energy absorption of composite light airplane [PDF]
[[abstract]]The main aim of this study was to explore the safety differences when using aluminum alloy and three different fiber reinforced composites as material for the cockpit and fuselage of light aircraft under crash landing.
Pu-Woei Chen
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Annealing-induced strengthening in hetero-structured Mg alloy laminates with gradient Al content
Journal of Magnesium and AlloysThis study developed a five-layer Mg alloy laminate (pure Mg/AZ31/AZ91/AZ31/ pure Mg) through an innovative synergistic strategy involving Al-element gradient design, extrusion, and short-term annealing.
Xiang Chen +9 more
doaj +1 more source
Influence and Simulation Study of Surface Coating Damage on Pitting Corrosion of 7B04 Aluminum Alloy
Journal of Aeronautical Materials, 2016 Self-corrosion and pitting corrosion of 7B04 aluminum alloy at different environment conditions were studied by electrochemical test with simulating surface coating damage on 7B04 aluminum alloy.
WANG Chenguang +3 more
doaj +1 more source
A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection
Advanced Engineering Materials, EarlyView.A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan +9 more
wiley +1 more source