Results 21 to 30 of about 631,740 (304)
International Journal of Electrochemical Science, 2021 The corrosion behavior of 6061 aluminum alloy under heat treatment at different temperatures and oxidation states was studied. The anode film was prepared by acidizing 6061 aluminum alloy as matrix. The effect of oxidation treatment on the microstructure
Zhisheng Wang +4 more
doaj +1 more source
Direct keyhole laser welding of aluminum alloy AA5754 to titanium alloy Ti6Al4V [PDF]
, 2014 The tensile strength of direct AA5754/Ti6Al4V joints performed by high speed Yb:YAG laser welding is found to be determined by morphology and phase content of dissimilar interface formed between contacting Al-rich and Ti-rich melted zones. Three types of
CICALA, E +6 more
core +1 more source
Stability checking method of pressure bars for suspended aluminum alloy single-piece bulkhead
Zhongguo Jianchuan Yanjiu, 2020 Objectives The suspended aluminum alloy integral plate frame structure is widely used in hovercrafts. In light of the low elastic modulus of aluminum alloy, the instability problem of the aluminum alloy frame structure is prominent and must be fully ...
WU Jianguo +3 more
doaj +1 more source
Influence of ultrasonic melt treatment on the formation of primary intermetallics and related grain refinement in aluminum alloys [PDF]
, 2011 This article is distributed under the terms of the Creative Commons Attribution Noncommercial License which permits any noncommercial use, distribution, and reproduction in any medium, provided the original author(s) and source are credited - The article
Eskin, D. G. +12 more
core +2 more sources
Grain refinement efficiency of a new oxide-containing master alloy for aluminium casting alloys [PDF]
, 2014 In this study, grain refinement efficiency of a new oxide master alloy based on MgAl2O4 was demonstrated on an A357 alloy. The grain size of the reference alloy was reduced by 50-60% with the addition of the master alloy and introduction of ultrasonic ...
Dmitry G. Eskin +7 more
core +1 more source
Combined Kelvin probe force microscopy and secondary ion mass spectrometry for hydrogen detection in corroded 2024 aluminium alloy [PDF]
, 2013 The capability of Kelvin probe force microscopy (KFM) to detect and locate hydrogen in corroded 2024 aluminium alloy was demonstrated. Hydrogen was introduced inside the 2024 alloy following a cyclic corrosion test consisting of cycles of immersion in 1 ...
Blanc, Christine +5 more
core +1 more source
Al-Khawarizmi Engineering Journal, 2019 Microwave heating is caused by the ability of the materials to absorb microwave energy and convert it to heat. The aim of this study is to know the difference that will occur when heat treating the high strength aluminum alloys AA7075-T73 in a microwave ...
Sadiq Jaffer Aziz +2 more
doaj +1 more source
Metals, 2023 Due to their exceptional all-around performance, steel/aluminum-alloy composite plates have been frequently utilized in many different industries. However, when steel/aluminum-alloy composite plates are prepared by the rolling process, they will scarcely
Chao Yu +4 more
doaj +1 more source
Generation and characterization of T40/A5754 interfaces with lasersPatrice [PDF]
, 2014 Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum
BERTHE, Laurent +5 more
core +1 more source
Metals, 2019 Three different aging treatments including single-aging, delayed-aging, and pre-aging were carried out on 6082 extruded profiles after solution heat treatment, then their hardness, tensile strength, and microstructure were tested.
Xin He +6 more
doaj +1 more source