Results 71 to 80 of about 481,866 (292)
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Materials Today AdvancesThe influence of relaxation and rejuvenation on the deformation behavior of the Zr-based bulk metallic glass Vit105 (Zr52.5Cu17.9Ni14.6Al10Ti5) was investigated, where a well-defined thermal history was systematically introduced by thermal treatments ...
Lucas M. Ruschel +8 more
doaj +1 more source
Materials & Design, 2020 The Finemet/FeSi compound powder cores with crystal-like microstructure were successfully fabricated by adding micron-size gas-atomized FeSi powders into the thick Finemet flaky-powders.
Zhili Guo +6 more
doaj +1 more source
Influence of an Argon/Silane Atmosphere on the Temperature of a Thermal Plasma
Advanced Engineering Materials, EarlyView.The influence of a silane‐doped argon atmosphere on the chemical composition and temperature of a thermal nontransferring argon plasma is investigated using optical emission spectroscopy. As a result of the high amount of free electrons resulting from the stepwise ionization and dissociation of the silane molecule, even a silane addition of 0.01 vol ...
Lena Kreie +4 more
wiley +1 more source
Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres
Advanced Engineering Materials, EarlyView.This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann +3 more
wiley +1 more source
Long-Term Stability of Two Thermoplastic Polymers Modified with Silver Nanoparticles
Nanomaterials, 2019 The aim of this study was to investigate the mechanical properties of polymeric composites prepared via extrusion and injection moulding. Four stable thermoplastic polymers were used as composites matrices (two kinds of polymethyl methacrylate and two ...
Magdalena Ziąbka, Michał Dziadek
doaj +1 more source
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Containerless processing of amorphous ceramics [PDF]
The absence of gravity allows containerless processing of materials which could not otherwise be processed. High melting point, hard materials such as borides, nitrides, and refractory metals are usually brittle in their crystalline form.
Krishnan, Shankar +3 more
core +1 more source
Application of Raman and Photoluminescence Spectroscopy to MgO‐C Refractories
Advanced Engineering Materials, EarlyView.Visible to near infrared luminescence of MgO is studied on MgO‐C bricks and nominally pure MgO powder, with focus on two similar sharp high‐intensity signals, at 699 and 871 nm, each surrounded by symmetrical sidebands. The nature of these sidebands is investigated by temperature‐dependent spectroscopic measurements, confirming phonon involvement by ...
Julia Richter +5 more
wiley +1 more source