Results 121 to 130 of about 30,094 (255)

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

open access: yesAdvanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin   +12 more
wiley   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

open access: yesAdvanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller   +3 more
wiley   +1 more source

Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel

open access: yesAdvanced Engineering Materials, EarlyView.
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe   +9 more
wiley   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

open access: yesAdvanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo   +15 more
wiley   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

open access: yesAdvanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi   +3 more
wiley   +1 more source

Microstructural, Mechanical, and Textural Evolution of Dissimilar Combination of Laser‐Welded Maraging Steel and 4340 Steel

open access: yesAdvanced Engineering Materials, EarlyView.
The present work reports the microstructural, mechanical, and texture evolution of a dissimilar combination laser‐welded maraging steel with 4340 steel. This is important for aerospace applications. The demand for dissimilar welding is growing rapidly with the requirement of efficient and durable joints.
Bharat Behl   +3 more
wiley   +1 more source

Adjusting Nucleation Chemistry for the Atomic Layer Deposition of Antimony Selenide on Metal Oxide Surfaces

open access: yesAdvanced Engineering Materials, EarlyView.
The ALD precursor bis(trimethylsilyl)selenide is simultaneously a substrate surface inhibitor. It allows for the growth of Sb2Se3 in combination with tris(dimethylamido)antimony, but also silylates surface hydroxyl groups on the substrate if such hydroxyls are present.
Pei‐Chun Liao   +9 more
wiley   +1 more source

Influence of Fe Particle Size Distribution on Chemical Homogeneity, Microstructure, and Crack Formation in Fe–SiC Powder Blends Processed by PBF‐LB/M

open access: yesAdvanced Engineering Materials, EarlyView.
The influence of Fe particle size on in situ alloying of Fe–SiC powder blends in PBF‐LB/M is revealed. Contrary to expectations, the coarser Fe fraction provides a broader crack‐free processing window and slightly improved elemental homogeneity while producing higher but more variable hardness. The results highlight a complex trade‐off between particle
Anna Luise Strauch   +2 more
wiley   +1 more source

Edible Cuttlefish Ink: Complex Chemistry, Structure, and Electrical Response

open access: yesAdvanced Engineering Materials, EarlyView.
An integrated approach of chemistry‐structure‐electrical properties is used to assess the potential of edible cuttlefish ink as a bio‐based conductive ink for printable electronics. Chromatography and Neutron Activation Analysis reveal a fascinating molecular and elemental diversity.
Camille Bour‐Cardinal   +5 more
wiley   +1 more source

Home - About - Disclaimer - Privacy