Results 241 to 250 of about 68,304 (312)

Planar Solid‐State Nanopores Toward Scalable Nanofluidic Integration Based on CMOS Technology

Advanced Engineering Materials, EarlyView.
We present a scalable silicon‐based fabrication strategy for planar solid‐state nanopores to enable their integration with complex nanofluidic systems. Prototype devices demonstrate normal voltage‐current characteristics, good noise performance, and appreciable streaming currents. Our CMOS‐compatible fabrication process offers precise geometric control
Ngan Hoang Pham, Chenyu Wen, Mohammad Hadi Khaksaran, Won‐Yong Lee, Javier Cruz, Klas Hjort, Dongping Wu, Shi‐Li Zhang   +7 more
wiley   +1 more source

Challenges of healthcare quality in Kenya's tertiary hospitals: assessing the contribution and constraints of asset leasing financing mechanism. [PDF]

BMC Health Serv Res
Karino E, Ndegwa J, Were V.
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Evaluating the efficacy of a personalised sub-symptomatic exercise treatment programme for rehabilitation of military service members with persistent symptoms following mild traumatic brain injury: a randomised controlled trial. [PDF]

BMJ Open Sport Exerc Med
Darr AJ, Kirlin LK, Lopez J, Caswell M, Ananthanarayanan M, Robb J, Haider MN, Kelly KR, Bailie JM.   +8 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

A Vision Language-Based Framework for Detecting Industrial Mechanical, Electrical, and Plumbing Assets Using Unlabelled Data. [PDF]

Sensors (Basel)
Kamali M, Atazadeh B, Rajabifard A, Chen Y, Javaherian Pour E.   +4 more
europepmc   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source

Distributional effects of marine conservation on coastal livelihoods in Eastern Indonesia. [PDF]

Nat Commun
Le DT, Ahmadia GN, Ratih IA, Claborn K, Estradivari, Lazuardi ME, Matualage D, Mohebalian PM, Nanlohy H, Pusparini NKS, Rasolofoson R, Salosso KE, Timisela NR, Pakiding F, Glew L, Mascia MB, Gill D.   +16 more
europepmc   +1 more source