Results 91 to 100 of about 519,289 (290)
Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling
Advanced Engineering Materials, EarlyView.Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer +3 more
wiley +1 more source
Helium Escape in Context: Comparative Signatures of Four Close-in Exoplanets
The Astrophysical JournalObservations of escaping atmospheres on close-in exoplanets show a wide range in the strength and morphology of He I 10830 Å and H I absorption. Scaling relations attempt to link the He I signal to X-ray and UV irradiation, mass loss, and bulk planetary ...
Anna Ruth Taylor +4 more
doaj +1 more source
Acute effects of a large bolide impact simulated by a global atmospheric circulation model [PDF]
The goal is to use a global three-dimensional atmospheric circulation model developed for studies of atmospheric effects of nuclear war to examine the time evolution of atmospheric effects from a large bolide impact.
Crutzen, P. J., Thompson, Starley L.
core +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
The long-term evolution of both the atmosphere and the surface of Mars can be understood by examining the history of volatiles in the Mars atmosphere, their non-atmospheric reservoirs, and the processes of exchange between the two.
Jakosky, Bruce M.
core +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
The Astrophysical Journal LettersThe recent discovery of “ultrahot” ( P < 1 day) Neptunes has come as a surprise: some of these planets have managed to retain gaseous envelopes despite being close enough to their host stars to trigger strong photoevaporation and/or Roche lobe overflow ...
Shreyas Vissapragada +18 more
doaj +1 more source
Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions
Advanced Engineering Materials, EarlyView.This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley +1 more source