Results 41 to 50 of about 462 (149)

Thermo-Mechanically Processed Multi-Phase Ductile Iron: Microstructure Development

open access: yes, 2010
Using thermo-mechanical simulator equipped with dilatometry system, two ductile iron alloys with different Mn-content are processed by combining both, well defined deformation process and subsequent controlled cooling in a single processing chain to ...
Mohamed Soliman   +2 more
core   +1 more source

Experimental and numerical assessment of fracture toughness of dual-phase austempered ductile iron [PDF]

open access: yes, 2009
The effects of the microstructure topology on the fracture toughness of dual-phase austempered ductile iron are studied in this paper by means of finite element modelling and experimental testing.
Sikora, Jorge Antonio   +7 more
core   +1 more source

Structural and Phase Analysis of the Ausferritic Ductile Cast Iron Matrix Obtained by Heat Treatment and in the Raw State

open access: yesC
This paper presents a comparative analysis of ausferritic ductile cast iron matrix obtained through heat treatment and in its raw state. Ausferrite without heat treatment was achieved by modifying the chemical composition, while nodular graphite was ...
Leszek Klimek   +4 more
doaj   +1 more source

Effect of sub-zero cooling on microstructure and mechanical properties of a low alloyed austempered ductile iron [PDF]

open access: yesChina Foundry, 2007
The effect of sub-zero cooling on microstructure and mechanical properties of a low alloyed austempered ductile iron has been investigated. Austempering of samples was performed at 325! and 400℃ after austenitizing at 875℃ and 950℃.
M. Ardestani, S. Yazdani
doaj  

Effect of Niobium on the Microstructure and Mechanical Properties of Alloyed Ductile Irons and Austempered Ductile Irons

open access: yesMetals, 2021
In this research, different ductile irons and austempered ductile irons were successfully developed using several alloying contents of nickel, copper and microalloying with niobium.
Mostafa Ahmed   +4 more
doaj   +1 more source

Analysis of mechanical properties and its associated fracture surfaces in dual-phase austempered ductile iron [PDF]

open access: yes, 2013
This work aims at evaluating the fracture surfaces of tensile samples taken from a new kind of ductile iron referred to as ‘dual-phase Austempered Ductile Iron (ADI)’, a material composed of ausferrite (regular ADI microstructure) and free (or ...
Sikora, Jorge Antonio   +2 more
core   +1 more source

EFFECT OF AUSTEMPERING TIMES ON THE MICROSTRUCTURES AND MECHANICAL PROPERTIES OF DUAL-MATRIX STRUCTURE AUSTEMPERED DUCTILE IRON (DMS-ADI)

open access: yes, 2022
In this study, the effect of the austempering times on the microstructures and mechanical properties of dual-matrix structure austempered ductile iron (DMS-ADI) was investigated.
UYAR, AHMET   +5 more
core   +1 more source

The Effect of Microstructure on the Water Embrittlement of Dual-Phase Austempered Ductile Irons

open access: yesMetals
This study investigates the effect of microstructure on water-induced embrittlement of dual-phase austempered ductile iron (ADI). Dual-phase ADI materials were produced by austenitization at 780, 800, 820, and 840 °C followed by austempering at 400 °C/1 ...
Petar Janjatović   +6 more
doaj   +1 more source

Microstructural and mechanical properties of Cu-Ni-Mn-Mo austempered ductile iron obtained from two-step hot air austempering

open access: yesJournal of Materials Research and Technology, 2020
In the present work, mechanical and microstructural properties of Austempered Ductile Iron (ADI) alloyed with Cu-Ni-Mn-Mo submitted to different hot air austempering cycles in a two-step mechanism were evaluated.
Leonardo Pereira   +3 more
doaj   +1 more source

Performance Evaluation of Austempered Ductile Iron Camshaft Low Alloyed with Vanadium on an Electric Spin Rig Test

open access: yesMetals, 2023
Arbomex S.A. de C. V. is one of the largest worldwide manufacturers of ductile cast iron camshafts, produced by means of the phenolic urethane no-bake sand mold casting method and cold box by stack molding technology.
Alejandro Cruz Ramírez   +3 more
doaj   +1 more source

Home - About - Disclaimer - Privacy