Results 151 to 160 of about 2,658 (208)

Effect of Cr, Mo and Al on Microstructure, Abrasive Wear and Corrosion Resistance of Ni-Mn-Cu Cast Iron. [PDF]

Materials (Basel), 2019
Medyński D, Samociuk B, Janus A, Chęcmanowski J.   +3 more
europepmc   +1 more source

Rolling Contact Fatigue Performances of Carburized and High-C Nanostructured Bainitic Steels. [PDF]

Materials (Basel), 2016
Wang Y, Zhang F, Yang Z, Lv B, Zheng C.
europepmc   +1 more source

Microstructure and cavitation erosion behavior in overlapping vs. substrate areas of WAAM NAB. [PDF]

Ultrason Sonochem
Cai X, Wang S, Miao D, Li S, Gao R, Qiao Y, Yang M, Zhou J, Zhang Q, Xue F.   +9 more
europepmc   +1 more source

Effect of Stress Ratio and Loading Frequency on the Corrosion Fatigue Behavior of Smooth Steel Wire in Different Solutions. [PDF]

Materials (Basel), 2016
Wang S, Zhang D, Hu N, Zhang J.
europepmc   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Austempering and Austempered Ductile Iron Microstructure in Copper Alloyed Ductile Iron

Journal of Materials Engineering and Performance, 2003
The variation in the austempered microstructure, the volume fraction of retained austenite, Xλ, the average carbon content of retained austenite, Cλ, their product XλCλ and the size of bainitic ferrite needles with austempering temperature for 0.6% Cu alloyed ductile iron have been investigated for three austempering temperatures of 270, 330, and 380 ...
Uma Batra, S. Ray, S. R. Prabhakar
openaire   +1 more source

Austempering kinetics of Cu-Ni alloyed austempered Ductile Iron

Metals and Materials International, 2014
The aim of the paper was to investigate the effect of austempering parameters (time and temperature) on the microstructure and mechanical properties of ADI alloyed with 1.5% Cu and 1.6% Ni (in wt.%) in order to establish the optimal processing window.
Erić-Cekić, Olivera, Šiđanin, Leposava, Rajnović, Dragan, Baloš, Sebastian   +3 more
openaire   +2 more sources

Austempered Ductile Iron for Gears

SAE Technical Paper Series, 2012
<div class="section abstract"><div class="htmlview paragraph">It is discussed the use of ADI (Austempered Ductile Iron) for gears. The gears were produced from continuous cast iron bars, heat treated for grade 3 of ASTM ADI Standard A897M-06 (UTS ≻1200 MPa), and compared to carburized steel AISI 8620 and to induction hardened steel AISI ...
Wilson Luiz Guesser, Fabio Koda, Jairo Alberto Blanco Martinez, Carlos Henrique da Silva   +3 more
openaire   +1 more source

Locally Austempered Ductile Iron (LADI)

SAE International Journal of Materials and Manufacturing, 2010
<div class="section abstract"><div class="htmlview paragraph">There are numerous component applications that would benefit from localized austempering (heat treating only a portion of the component) for either improved wear properties or fatigue strength.
Christopher A. Bixler, Kathy L. Hayrynen, John Keough, George Pfaffmann, Scott Gledhill   +4 more
openaire   +1 more source

Austempered ductile irons-gears

Materials & Design, 1985
Abstract Both the technical and commercial competitive nature of austempered ductile irons for manufacturing gears are described and some of the current applications of these gears are outlined.
openaire   +1 more source

AUSTEMPERED DUCTILE IRON

Alloy Digest, 1986
Abstract AUSTEMPERED DUCTILE IRON has high strength with excellent toughness and ductility. Its strength is twice that of conventional ductile irons, comparable to heat-treated wrought steels. Composition is balanced to provide foundry compatibility, minimal segregation and good response to austempering.
openaire   +1 more source