Results 41 to 50 of about 374 (167)
steel research international, Volume 96, Issue 12, Page 211-227, December 2025.A new austempering approach following intercritical austenitizing is explored to improve the mechanical behavior of API 5CT steel. By tailoring ferrite–bainite microstructures, the process achieves a balance of strength and ductility without the need for post‐quench tempering. The results highlight a cost‐effective alternative to conventional quenching
Paulo Henrique Cirilo +2 more
wiley +1 more source
Effect of two-step austempering on fatigue behavior of austempered ductile iron (ADI) [PDF]
SN Applied Sciences, 2019 The effect of two-step austempering on the fatigue properties in alloyed ductile iron was studied. The ductile irons were subjected to conventional and two-step austempering processes. The austempering process was performed by making three batches. In the first batch, samples after austenitizing at 900 °C were conventionally austempered separately at ...
C. S. Wadageri, R. V. Kurahatti
openaire +1 more source
Journal of Materials Research and Technology, 2023 In this study, the multi-scale microstructures of bainitic steel were refined to different degrees by austempering below Ms (martensite start temperature). The influence of multi-scale microstructures and their boundaries on impact toughness was analyzed.
Kun Wang +6 more
doaj +1 more source
Highsilicone Austempered Ductile Iron
Archives of Foundry Engineering, 2014 Abstract Ductile iron casts with a higher silicone content were produced. The austempering process of high silicone ductile iron involving different austempering times was studied and the results presented. The results of metallographical observations and tensile strength tests were offered. The obtained results point to the fact that the silicone
A. Kochański +2 more
openaire +1 more source
Thermomechanical Processing, Microstructure, and Mechanical Properties of Medium‐Mn Steel
steel research international, Volume 96, Issue 12, Page 252-260, December 2025.The microstructure evolution and mechanical properties of a medium‐Mn steel are investigated after thermomechanical processing and isothermal holding at various temperatures. A fine multiphase structure of bainite, fresh or tempered martensite, and retained austenite are obtained.
Burak Barutçuoğlu +3 more
wiley +1 more source
Effect of alloying elements on austempered ductile iron (ADI) properties and its process: Review [PDF]
China Foundry, 2015 Austempered ductile iron (ADI) parts have a unique combination of high strength and toughness with excellent design flexibility and low cost. These excellent properties are directly related to its microstructure called "ausferrite" that is the result of ...
Amir Sadighzadeh Benam
doaj
A Statistical Review of Hydrogen Effects on the Fatigue and Fracture Behavior of Steel
Fatigue &Fracture of Engineering Materials &Structures, Volume 48, Issue 9, Page 3613-3644, September 2025.ABSTRACT This study conducts a statistical re‐analysis of experimental data from the literature to assess the influence of hydrogen on key mechanical properties, including the medium‐/high‐cycle fatigue strength and the threshold value of the stress intensity factor range.
H. Wang +4 more
wiley +1 more source
Journal of Applied Crystallography, Volume 52, Issue 5, Page 1144-1156, October 2019., 2019 The single‐crystal elastic constants of polycrystalline titanium alloys have been determined using neutron and synchrotron powder diffraction.Single‐crystal elastic constants have been derived by lattice strain measurements using neutron diffraction on polycrystalline Ti‐6Al‐4V, Ti‐6Al‐2Sn‐4Zr‐6Mo and Ti‐3Al‐8V‐6Cr‐4Zr‐4Mo alloy samples.
Alexander Heldmann +8 more
wiley +1 more source
Very High Cycle Fatigue Performance of Ductile Cast Iron With Different Microstructures
Fatigue &Fracture of Engineering Materials &Structures, Volume 48, Issue 9, Page 3950-3966, September 2025.ABSTRACT The very high cycle fatigue performance of four ductile cast irons, a solid solution strengthened ferritic, ferritic‐pearlitic, and two austempered ductile cast irons, was investigated by ultrasonic fatigue testing under fully reversed loading conditions. The step‐stress fatigue testing method incorporating re‐use of runouts was employed, with
Max Ahlqvist +3 more
wiley +1 more source
Mathematical Problems in Engineering, Volume 2013, Issue 1, 2013., 2013 Austempered ductile iron has emerged as a notable material in several engineering fields, including marine applications. The initial austenite carbon content after austenization transform but before austempering process for generating bainite matrix proved critical in controlling the resulted microstructure and thus mechanical properties. In this paper,
Chan-Yun Yang +4 more
wiley +1 more source