Results 51 to 60 of about 2,010 (151)

Thermodynamic calculation of phase equilibria in stainless steels [PDF]

Journal of Mining and Metallurgy. Section B: Metallurgy, 2012
In this paper two examples of thermodynamic investigation of stainless steels using both, experimental and modeling approach are described. The ferritic-austenitic duplex stainless steel and austenitic stainless steel were investigated using thermal ...
Klančnik G., Petrovič Steiner D., Medved J.   +2 more
doaj   +1 more source

Tailoring Laser Powder Bed Fusion and Post‐Processing Parameters for JIS SKD61 Tool Steels: Surface Roughness, Microstructure, and Mechanical Properties

steel research international, EarlyView.
Laser powder bed fusion of JIS SKD61 tool steel is systematically optimized using a Taguchi design and ANOVA. Hatch spacing and layer thickness are identified as dominant parameters controlling surface roughness and tensile strength. Subsequent tempering at 600°C improves microstructural stability and mechanical performance, enabling high‐density SKD61
Masrurotin Masrurotin, Andi Ard Maidhah, Maziar Ramezani, Wojciech Macek, Cho‐Pei Jiang   +4 more
wiley   +1 more source

Grain growth kinetics and hardness empirical model of 253 MA austenitic stainless steel after multi-pass cold rolling

Engineering and Applied Science Research, 2022
This study investigated changes in the average grain size and hardness values of 253 MA austenitic stainless steel (ASS) and determined the grain growth kinetics as well as a hardness empirical model. A 35% multi-pass cold rolling process was employed to
Rana K. Melinia, Moch. Syaiful Anwar, Robert R. Wijaya, Eddy S. Siradj   +3 more
doaj  

Mix structure of high nitrogen austenitic stainless steel and 316L stainless steel formed by wire and arc additive manufacturing based on size controlling of beads

Cailiao gongcheng, 2020
Wires of high nitrogen austenitic stainless steel and 316L stainless steel were used, the surface forming characteristics of single bead, single-bead multi-layer and single-layer multi-bead were analyzed on high nitrogen austenitic stainless steel ...
YAO Xiang-hong, ZHOU Qi, WANG Ke-hong, ZHANG Xiao-yong   +3 more
doaj   +1 more source

Creep Performance of Stainless Steel 316 Brackets: Insights From Conventional and Advanced Modeling Approaches

steel research international, EarlyView.
Creep behavior of SS 316 brackets is examined through experiments, conventional creep laws, and advanced constitutive modeling. Long‐term deformation, stress redistribution, and life prediction are compared under service‐relevant loads. The study highlights the limits of classical models and demonstrates improved accuracy using advanced approaches for ...
Mohsin Sattar, Jan Hosek, Maaz Akhtar, Uliana Finaeva, Muhammad Muzamil, Naser A. Alsaleh, Asad A. Zaidi, Barun Haldar   +7 more
wiley   +1 more source

OPTIMIZATION OF SURFACE ROUGHNESS OF AISI 304 AUSTENITIC STAINLESS STEEL IN DRY TURNING OPERATION USING TAGUCHI DESIGN METHOD [PDF]

Journal of Engineering Science and Technology, 2010
The present work is concentrated with the dry turning of AISI 304 Austenitic Stainless Steel (ASS). This paper presents the influence of cutting parameters like cutting speed, feed rate and depth of cut on the surface roughness of austenitic stainless ...
D. PHILIP SELVARAJ, P. CHANDRAMOHAN
doaj  

Microstructure Characterization of Bending Effects in 304L Stainless Steel Cladded with Low‐Alloy Steel Weld

steel research international, EarlyView.
Prebending of 304L/Q345R cladded plates significantly alters the subsequent weld thermal cycle and modifies the local interfacial microstructure. Combined electron backscatter diffraction (EBSD) and microscopy analysis demonstrates that deformation twinning, martensitic transformation, and defect initiation are concentrated at the trimaterial junction,
Ali Fahem, Elsiddig Elmukashfi, Hong Dong   +2 more
wiley   +1 more source

Microstructure and Properties of Low-nickel Austenitic Stainless Steel14.0Cr-1.1Ni-9.2Mn-0.30Cu

Teshugang, 2023
14.0Cr- 1. 1Ni-9.2Mn-0.30Cu stainless steel was developed on the basis of13.36Cr- 1. 12Ni- 11.2Mn low-nickel austenitic stainless steel, and the metallographic structure, microstructure, mechanical properties and forming properties of austenitic ...
吴海林, 陈小龙, 钱学海, 曾垚, 陈盛淋   +4 more
doaj  

Computer Modeling of the Ferrite‐To‐Austenite Transformation in a Super‐Duplex Stainless Steel and the Important Role of Trans‐Interface Diffusion

steel research international, EarlyView.
An accurate moving boundary model for volume diffusion containing boundary conditions from trans‐interface diffusion (TID) simulates the austenite growth during cooling. TID of Cr, Mo, N and Ni enhance growth kinetics. Without TID, compositions of the interface region change, decreasing the driving force for growth and finally causing numerical ...
A. Salwén, T. Müller, S. Nouhi, J. Y. Jonsson   +3 more
wiley   +1 more source

Tailored Hardening and Isothermal Bainitizing of Additively Manufactured Nitrogen‐Enhanced Martensitic Chromium Steel

steel research international, EarlyView.
Tailored heat treatments transform additively manufactured high‐nitrogen martensitic Cr steel from austenitic as‐built condition to high‐hardness states. Isothermal bainitizing at 250°C generates an ultrafine nanostructure and achieves higher hardness than conventional hardening and tempering, highlighting a promising postprocessing route for laser ...
Philip König, Sebastian Weber, Jonathan Lentz   +2 more
wiley   +1 more source