Results 91 to 100 of about 947 (168)
Importance of austenitization temperature and ausforming on creep strength in 9Cr ferritic/martensitic steel [PDF]
, 2018 Small Punch Creep technique was used as a screening procedure to evaluate the creep properties of different microstructures developed in a thermomechanical simulator.
E. Altstadt +9 more
core +1 more source
steel research international, Volume 97, Issue 8, Page 4363-4381, August 2026.This study validates a recycling pathway for converting interconnect assemblies from end‐of‐life SOC stacks into commercial‐grade AISI 304 steels. Using scrap‐based steelmaking operations, austenitic cast steels with <4.0% δ‐ferrite are successfully produced.
Jeraldine Lastam +7 more
wiley +1 more source
Nuclear Materials and Energy, 2018 Among the options currently taken into account for the realization of the first DEMO reactor there are the “helium-cooled” and the “dual coolant” breeding blanket.
C. Cristalli +5 more
doaj +1 more source
steel research international, Volume 97, Issue 8, Page 4326-4336, August 2026.Surface reconditioning through mechanical and electrochemical polishing is shown to extend the fatigue life of predamaged 42CrMo4 steel by over 12 times. By removing ≈100 μm of surface material, surface‐driven fatigue damage is mitigated. This study introduces a reuse potential metric to evaluate fatigue recovery and support sustainable steel reuse. To
Ayush Shrivastava +7 more
wiley +1 more source
Exploiting Residual Elements Arising from Scrap Steel in Future Sustainable Steel Alloy Design
steel research international, Volume 97, Issue 8, Page 4270-4281, August 2026.Herein, the effects of residual elements Cu and Sn on grain growth, recrystallization, and phase transformation in C–Mn steel are summarized, and a case study is presented on how the presence of residual elements can be exploited to reduce deliberate Nb microalloying while achieving the same grain size control and strength during thermomechanical ...
Claire Davis +5 more
wiley +1 more source
Microstructure and mechanical properties of ADI depending on austenitization methods and parameters [PDF]
, 2012 Ductile iron was quenched using two-variant isothermal transformation. The first treatment variant consisted of one-phase austenitization at a temperature t = 830, 860 or 900 C, cooling down to an isothermal transformation temperature of 300 or 400 C and
Szykowny, T., Giętka, T.
core
steel research international, Volume 97, Issue 8, Page 4067-4084, August 2026.This review explains how impurities from recycled scrap affect steel production and performance. Even small amounts (far below 1%) of these impurities can change how steel behaves during fabrication but also affect the properties of the end product. With better understanding and targeted countermeasures, these challenges can be managed, enabling wider ...
Oleksandr Glushko, Ronald Schnitzer
wiley +1 more source
MetalsA modified carbide-free bainite (CFB) steel has been developed, building on existing alloys for compatibility with commercial continuous annealing lines (CALs), featuring a low austenitization temperature and short overaging time.
Bahareh Mobedpour +2 more
doaj +1 more source
A Novel Two Step Austenitization Process To Produce Austempered Ductile Iron (adi) With High Strength, Ductility And Fracture Toughness [PDF]
, 2021 A novel, Two-Step Austenitizing heat treatment process for creation of Austempered Ductile Iron (ADI) with an optimum combination of strength, ductility and fracture toughness was conceived in this investigation.
Joshi, Deepak
core
Results in Surfaces and InterfacesSteel cylinders are widely used in industry, but their service life is often limited by corrosion and wear. Conventional coating methods generally produce only mechanical bonds and can lead to delamination and interfacial failure.
Jamiatul Akmal +4 more
doaj +1 more source