Results 271 to 280 of about 212,828 (333)
Some of the next articles are maybe not open access.
Renewable Energy, 2019
The present study investigates biodiesel production from waste palm oil (WPO) using coconut coir husk (CCH) derived solid acid catalyst. The catalyst was prepared by the direct in-situ concentrated sulfuric acid impregnation. The presence of active sites,
Indika Thushari +2 more
semanticscholar +1 more source
The present study investigates biodiesel production from waste palm oil (WPO) using coconut coir husk (CCH) derived solid acid catalyst. The catalyst was prepared by the direct in-situ concentrated sulfuric acid impregnation. The presence of active sites,
Indika Thushari +2 more
semanticscholar +1 more source
Towards a digital twin for mitigating void formation during debulking of autoclave composite parts
, 2020High-performance polymeric composites are increasingly used in the design of aircraft structural components; however, susceptibility to manufacturing irregularities, including porosity/voids, remains a primary challenge delaying the implementation of ...
G. Seon +3 more
semanticscholar +1 more source
, 2020
Global fisheries production has increased up to 200 MT which resulted in 20 MT of waste. Discards or by-products from aquatic processing have remained a big challenge for waste management and their efficient use for human food.
A. Nawaz +7 more
semanticscholar +1 more source
Global fisheries production has increased up to 200 MT which resulted in 20 MT of waste. Discards or by-products from aquatic processing have remained a big challenge for waste management and their efficient use for human food.
A. Nawaz +7 more
semanticscholar +1 more source
ACS Applied Materials and Interfaces
Composite laminates utilizing autoclave-grade carbon fiber-reinforced plastic (CFRP) prepreg were manufactured using a polymer nanoporous network (NPN) interlayer that generates capillary pressure in lieu of pressure from an autoclave.
C. Li +8 more
semanticscholar +1 more source
Composite laminates utilizing autoclave-grade carbon fiber-reinforced plastic (CFRP) prepreg were manufactured using a polymer nanoporous network (NPN) interlayer that generates capillary pressure in lieu of pressure from an autoclave.
C. Li +8 more
semanticscholar +1 more source
Journal of Microencapsulation, 1994
The attempt was made to study liposome stability and oxidation under the autoclaving conditions. It was shown that after the preliminary air removal from a liposome sample there was no lipid oxidation (malonaldehyde bis(dimethyl acetate) was used as a control) and liposome content leakage during autoclaving.
A N, Lukyanov, V P, Torchilin
openaire +2 more sources
The attempt was made to study liposome stability and oxidation under the autoclaving conditions. It was shown that after the preliminary air removal from a liposome sample there was no lipid oxidation (malonaldehyde bis(dimethyl acetate) was used as a control) and liposome content leakage during autoclaving.
A N, Lukyanov, V P, Torchilin
openaire +2 more sources
Digital twin enhanced fault diagnosis reasoning for autoclave
Journal of Intelligent Manufacturing, 2023Yucheng Wang +4 more
semanticscholar +1 more source
Heat transfer simulation and improvement of autoclave loading in composites manufacturing
The International Journal of Advanced Manufacturing Technology, 2021S. Mirzaei +4 more
semanticscholar +1 more source
1995
Abstract Autoclave molding is a process used to impart a controlled heat and pressure cycle cure to a layup. This article describes the materials used for preparing a layup, including peel ply, separator, bleeder, barrier, breather, dam, and vacuum bag.
openaire +1 more source
Abstract Autoclave molding is a process used to impart a controlled heat and pressure cycle cure to a layup. This article describes the materials used for preparing a layup, including peel ply, separator, bleeder, barrier, breather, dam, and vacuum bag.
openaire +1 more source