Results 121 to 130 of about 30,823 (299)

Fatigue Crack Initiation and Growth in Nanocrystalline Ni at Multiple Length‐Scales

Advanced Engineering Materials, EarlyView.
Overview of miniaturized in situ SEM fatigue setup and resultant fatigue crack growth data for nanocrystalline Ni. The presented study focuses on the analysis of fatigue crack growth rate (FCGR) in focused ion beam‐notched microcantilevers prepared from nanocrystalline (NC) Ni as a model material.
Igor Moravcik, Alexander Jelinek, Markus Alfreider, Jutta Luksch, Anton Hohenwarter, Florian Schaefer, Christian Motz, Daniel Kiener   +7 more
wiley   +1 more source

Effect of Axial Pre-Compression on Lateral Performance of Masonry Under Cyclic Loading

, 2011
Strengthening of masonry against seismic events is very essential and getting maximum attention of researchers around the globe. An extensive experimental program was carried out to study the in-plane lateral performance of un-reinforced masonry ...
Asadullah Qazi, Syed HassanFarooq, Muhammad Ilyas   +2 more
core  

Research on Seismic Performance of Assembled Steel–Concrete Composite Joints in the Top Layer of Subway Station Under High Axial Compression Ratio

Buildings
In view of the adverse effect of the failure mode of the “strong beam and weak column” at the top-layer joint of subway stations on structural seismic performance under high axial compression ratio, a novel assembled steel–concrete composite (ASCC) beam ...
Haoxuan Li, Jisheng Qiu, Leilei Li, Qing Qin, Yuqing Zhang, Guanghong Xiong, Shurui Wang   +6 more
doaj   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

On the performance of a nonlinear vibration isolator consisting of axially loaded curved beams [PDF]

, 2013
A desirable characteristic for nonlinear vibration isolators is a high static stiffness and a low dynamic stiffness. A curved beam is a possible candidate for this role provided that the amplitude of vibration about the static equilibrium position is ...
Brennan, MJ, Abolfathi, Ali, Waters, Tim P., Brennan, Michael J., Waters, TP, Abolfathi, A   +5 more
core  

Effect of steel fibres and expansive agents on compressive behaviour of circular CFST columns

Case Studies in Construction Materials
Concrete filled steel tube columns (CFSTCs) are commonly used in large-span bridges and high-rise buildings. As the shrinkage of concrete may lead to significant degradation in the mechanical performance of CFSTCs, expansive concrete or fibre reinforced ...
Xianwen Hu, Tian-hang Su, Jun-Jie Zeng, Yuen-ling Long, Jing-Sheng Wang, JinJing Liao, Yi Ouyang   +6 more
doaj   +1 more source

Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying

Advanced Engineering Materials, EarlyView.
An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara, Vincent Rat, Quentin Dubreuil, Patrice Valorge, Simon Goutier, Alain Denoirjean, Olivier Messe, Céline Ruelle, Jean‐Philippe Poli   +8 more
wiley   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source