Results 71 to 80 of about 2,046 (263)
Numerical study of probe parameters on performance of a transonic axial compressor. [PDF]
PLoS One, 2021 Islam A, Ma H.
europepmc +1 more source
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy
Advanced Engineering Materials, EarlyView.A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal +4 more
wiley +1 more source
Artificial Neural Network Structure Optimisation in the Pareto Approach on the Example of Stress Prediction in the Disk-Drum Structure of an Axial Compressor. [PDF]
Materials (Basel), 2022 Kozakiewicz A, Kieszek R.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Advanced Engineering Materials, EarlyView.Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati +11 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley +1 more source
Simulation of Casing Treatments of a Transonic Compressor Stage
International Journal of Rotating Machinery, 2008 This article presents the study of casing treatments on an axial compressor stage for improving stability and enhancing stall margin. So far, many simulations of casing treatments on single rotor or rotor-stator configurations were performed.
M. Hembera, H.-P. Kau, E. Johann
doaj +1 more source