Results 51 to 60 of about 4,100,444 (345)
Parameter Optimization of Tunnel Oxide Passivated Back Contact (TBC) Solar Cells
EnergiesTraditional simulation work often starts from the study of the impact of a single factor on device performance to obtain the optimal value of that factor and then regards the combination of the optimal values of each factor as the optimization condition.
Yang Chen +3 more
doaj +1 more source
African Vision and Eye Health, 2014 Discomfort when wearing contact lenses, especially rigid contact lenses, is a common complaint amongst neophyte as well as experienced contact lens wearers. Wearing a piggy-back system of contact lenses has been shown to improve comfort and wearing time,
W. D.H. Gillan
doaj +1 more source
Cell wall target fragment discovery using a low‐cost, minimal fragment library
FEBS Letters, EarlyView.LoCoFrag100 is a fragment library made up of 100 different compounds. Similarity between the fragments is minimized and 10 different fragments are mixed into a single cocktail, which is soaked to protein crystals. These crystals are analysed by X‐ray crystallography, revealing the binding modes of the bound fragment ligands.
Kaizhou Yan +5 more
wiley +1 more source
Well Intended Contact Failures on Interdigitated Back Contact Solar Cells
SiliconPV Conference ProceedingsThe interconnection of the cells that make up a solar panel is a simple step, but it is not unimportant. The panels are made up of cells in series, so that a poorly connected cell can spoil the good performance of the entire panel.
Yeray Mateos +6 more
doaj +1 more source
Simulation Results: Optimization of Contact Ratio for Interdigitated Back-Contact Solar Cells
International Journal of Photoenergy, 2017 In the fabrication of interdigitated back contact (IBC) solar cells, it is very important to choose the right size of contact to achieve the maximum efficiency.
Vinay Budhraja +2 more
doaj +1 more source
Journal of Applied Sciences and Environmental Management, 2022 Device simulation was employed to investigate the effect of metal back contact electrodes on the performance of n-type CdS/p-CIGS thin film solar cells using varying thicknesses of absorber layer at operating temperature of 300K.
M.A. Salawu +5 more
doaj +1 more source
Suns-V$_\textrm{OC}$ characteristics of high performance kesterite solar cells
, 2014 Low open circuit voltage ($V_{OC}$) has been recognized as the number one problem in the current generation of Cu$_{2}$ZnSn(Se,S)$_{4}$ (CZTSSe) solar cells. We report high light intensity and low temperature Suns-$V_{OC}$ measurement in high performance
Gokmen, Tayfun +2 more
core +1 more source
On the Mechanism of the Step Coverage of Blanket Tungsten Chemical Vapor Deposition [PDF]
, 1993 In this study, computer modeling of the contact fill process with chemical vapor deposition, (CVD) of tungsten is usedto show the importance of several details on the quality of the fill process. The effect of surface curvature on the stepcoverage of CVD-
Hasper, A., Schmitz, J.E.J.
core +2 more sources
Structural biology of ferritin nanocages
FEBS Letters, EarlyView.Ferritin is a conserved iron‐storage protein that sequesters iron as a ferric mineral core within a nanocage, protecting cells from oxidative damage and maintaining iron homeostasis. This review discusses ferritin biology, structure, and function, and highlights recent cryo‐EM studies revealing mechanisms of ferritinophagy, cellular iron uptake, and ...
Eloise Mastrangelo, Flavio Di Pisa
wiley +1 more source
Energy Science & Engineering, 2019 While the major function of molybdenum (Mo) back contact on soda‐lime glass (SLG) substrate in Cu(In,Ga)Se2 (CIGS) solar cells is to provide good adhesion and good conductivity, its role as the transportation channel for alkali elements from SLG ...
Junbo Gong +7 more
doaj +1 more source