Results 1 to 10 of about 731 (178)
Bainitic Ferrite Plate Thickness Evolution in Two Nanostructured Steels. [PDF]
Materials (Basel), 2021 Bainitic ferrite plate thickness evolution during isothermal transformation was followed at the same holding temperatures in two nanostructured steels containing (in wt.%) 1C-2Si and 0.4C-3Si. A dynamic picture of how the bainitic transformation evolves was obtained from the characterization of the microstructure present at room temperature after full ...
Ruiz-Jimenez V +3 more
europepmc +5 more sources
Further evidence of tetragonality in bainitic ferrite [PDF]
Materials Science and Technology, 2015 There is growing evidence that bainitic ferrite which retains a substantial amount of carbon in solid solution does not have cubic symmetry. We provide additional data on a different nanostructured bainitic steel to support this evidence, based on synchrotron X-ray diffraction experiments.
Christopher Hulme +2 more
exaly +4 more sources
Experimental evidence for non-cubic bainitic ferrite [PDF]
Scripta Materialia, 2013 The first evidence is provided for the existence of a tetragonal or slightly orthorhombic unit cell of bainitic ferrite. It supports the hypothesis that the excess carbon that persists in the ferrite, which is in contact with austenite, is a consequence of an increased solubility due to the change in symmetry from the conventional cubic unit cell.
Christopher Hulme, H K D H Bhadeshia
exaly +3 more sources
Metals, 2022 In this paper, a new low-carbon alloy gear steel is designed via Si/Al alloying. The carburizing and austempering, at a temperature slightly higher than the martensitic transformation point (Ms) of the surface and much lower than the Ms of the core, for ...
Yanhui Wang, Dong Xu, Zhinan Yang
exaly +3 more sources
Design concept and phase transformation study of advanced bainitic-austenitic medium-Mn steel [PDF]
Scientific ReportsThe isothermal heat treatment processing routes are designed for a novel 0.17 C-3.1Mn-1Si-0.55Al-0.22Mo-0.034Ti-0.073 V steel, aiming to obtain a homogeneous fine lath-type microstructure consisting of bainitic ferrite and retained austenite (RA).
Anna Wojtacha +6 more
doaj +2 more sources
Metals, 2019 In this study, the effects of Cr and Mo additions on mechanical properties of hot-forged medium carbon TRIP-aided bainitic ferrite (TBF) steel were investigated.
Koh-Ichi Sugimoto +1 more
exaly +3 more sources
Effect of Bainite to Ferrite Yield Strength Ratio on the Deformability of Mesostructures for Ferrite/Bainite Dual-Phase Steels [PDF]
Materials, 2021 The strength and plasticity balance of F/B dual-phase X80 pipeline steels strongly depends on deformation compatibility between the soft phase of ferrite and the hard phase of bainite; thus, the tensile strength of ferrite and bainite, as non-negligible factors affecting the deformation compatibility, should be considered first.
Gui-Ying Qiao +5 more
openaire +2 more sources
Metals, 2023 Three-dimensional microstructures of bainitic ferrites and prior austenite grains (PAGs) were observed in the initial stage of upper bainite transformation by using a serial sectioning technique and orientation analysis by electron back scattering ...
Shotaro Jimbo, Shoichi Nambu
doaj +1 more source
Metals, 2021 The mechanical properties of carbide-free bainitic steels used in sports equipment were investigated. The nanobainitic ferrite was introduced in bainitic steel to enhance the stability of blocky retained austenite (RA).
Han Meng +4 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 Ausforming at 900 °C with 30% reduction in V and N micro-alloyed steel could induce VN precipitation, which has low lattice misfit (1.8%) with bainitic ferrite in a particular crystal orientation.
Xiaojie Zhao +4 more
doaj +1 more source