Results 61 to 70 of about 124,930 (306)
Material recycling of inorganic sludge by wet ball milling [PDF]
, 2009 The possibility of material recycling of inorgamic sludge by wet ball milling with distrilled water and an ethylenediaminetetraacetic acid disodium salt dehydrate (EDTA・2Na・2H(2)O)reagent was investigated.
Benino, Yasuhiko +3 more
core
New CaO-based adsorbents prepared by solution combustion and high-energy ball-milling processes for CO2 adsorption: Textural and structural influences [PDF]
, 2017 New CaO-based adsorbents prepared by solution combustion and high-energy ball-milling processes for CO2 adsorption: Textural and structural influencesIn the present work, new CaO-based adsorbents were obtained by a fast solution combustion method and ...
GRANADOS CORREA, FRANCISCO +7 more
core +1 more source
Optimization for preparing Bi1.68Pb0.32Sr1.75Ca1.85Cu2.85O10+y powders by wet ball milling
Materials Research Express, 2022 Superconducting Bi _1.68 Pb _0.32 Sr _1.75 Ca _1.85 Cu _2.85 O _10+ _y (Bi-2223) powders were prepared by a conventional solid-state reaction using hand grinding and wet ball milling.
Yingwei Chen +8 more
doaj +1 more source
Frontiers in Materials, 2022 The addition of 4 wt% Zr to Ti52V12Cr36 alloy was carried out in two different ways: arc-melting or ball-milling. The cast alloy showed rapid hydrogen absorption up to 3.6 wt% of hydrogen capacity within 15 min.
Amol Kamble +2 more
doaj +1 more source
Advanced Functional Materials, EarlyView.This work explores Li‐substituted P2 layered oxides for Na‐ion batteries by crystallographic and electrochemical studies. The effect of lithium on superstructure orderings, on phase transitions during synthesis and electrochemical cycling and on the interplay of O‐ versus TM‐redox is revealed via various advanced techniques, including semi‐simultaneous
Mingfeng Xu +5 more
wiley +1 more source
Material recycling of inorganic slag by wet ball milling [PDF]
, 2012 The possibility of material recycling of inorganic slag by wet ball milling with distilled water and an ethylenediaminetetraacetic acid disodium salt dehydrate (EDTA·2Na·2H2O) reagent was investigated.
Benino, Yasuhiko +2 more
core
Development and Characterization of Mg-SiC Nanocomposite Powders Synthesized by Mechanical Milling [PDF]
, 2017 Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG geförderten) Allianz- bzw. Nationallizenz frei zugänglich.This publication is with permission of the rights owner freely accessible due to an Alliance licence and a national licence
Fleck, Claudia +4 more
core +1 more source
Effect of ball milling process on the photocatalytic performance of CdS/TiO2 composite
Nanotechnology Reviews, 2020 CdS/TiO2 composite photocatalysts were made by the method of secondary ball milling at different ball milling speeds, milling time, and material ratios. After the secondary ball milling process, parts of the samples were calcined at high temperatures.
Ye Mengya +4 more
doaj +1 more source
Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions
Advanced Functional Materials, EarlyView.DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng +7 more
wiley +1 more source
Comparison of equivalent ball milling processes on Fe70Zr30 and Fe70Nb30 [PDF]
, 2012 Dynamical analysis of the movement of a single ball in a planetary ball mill yields a cubic law with the frequency of the mill for the power released during the process.
Blázquez Gámez, Javier Sebastián +3 more
core +1 more source