Results 41 to 50 of about 124,550 (307)
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source
Analysis of magnetic and structural properties in La0.6Sr 0.4MnO3 ferromagnetic particles under the influence of mechanical ball milling effect [PDF]
, 2013 We have investigated the magnetic, structural and morphological properties of La0.6Sr0.4MnO3 (LSMO-40) manganite particles, synthesized by solid state reaction method.
Arnache O. +5 more
core +2 more sources
Advanced Engineering Materials, EarlyView.ZnS‐MXene‐TiO2 nanocomposite heterojunction for photocatalytic decomposition of this methylene blue dye (MB) greatly improves light absorption, charge separation, and active site area. Two‐dimensional MXene forms nanocomposites by easily combining them with 0D (quantum dots), 1D (tube and wire), 2D (plane and sheet), and 3D (particle and lamellar ...
Latiful Kabir +7 more
wiley +1 more source
Performance of laser assisted micro-milling (laμmill) of titanium alloy using micro ball end mill [PDF]
, 2018 Laser assisted milling technique turns to be complicated and unpredictable when the machining size is scaled to micro level. Furthermore, less has been reported on the application of ball end mill in laser assisted micro milling.
Mohid, Zazuli
core
Evolution of crystallite size, lattice parameter and internal strain in Al precipitates during high energy ball milling of partly amorphous Al87Ni8La5 alloy [PDF]
, 2014 The effects of plastic deformation by ball milling on the structure of a partly amorphous Al87Ni8La5 alloy were investigated by X ray diffractometry. Lattice parameter, crystallite size and lattice strain of the fcc Al precipitates were determined by ...
Dittrich, M., Schumacher, G.
core +2 more sources
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
Material recycling of inorganic sludge by wet ball milling [PDF]
, 2009 The possibility of material recycling of inorgamic sludge by wet ball milling with distrilled water and an ethylenediaminetetraacetic acid disodium salt dehydrate (EDTA・2Na・2H(2)O)reagent was investigated.
Benino, Yasuhiko +3 more
core
Roughness evolution of previously milled samples along a polishing test [PDF]
, 2016 In the present work results about roughness evolution along a polishing operation with corundum disks of size Norton 400 are presented. Hardened steel and hardened stainless steel samples were previously subjected to ball-end milling or side milling with
Buj Corral, Irene, Vivancos Calvet, Joan
core +2 more sources
Advanced Engineering Materials, EarlyView.Low‐consumable nickel ferrite‐based anodes for the Hall–Héroult process are compared with conventional prebaked carbon anodes using thermodynamic simulation and prospective life cycle assessment under contrasting future electricity system pathways from 2025 to 2050.
Felipe Alejandro Garcia Paz +6 more
wiley +1 more source
Nanostructured Al/Ni energetic composites: processing, reaction properties and activation energy
Journal of Materials Research and Technology, 2022 In this study, the nanostructured Al/Ni energetic composites were processed using the high-energy ball milling method. The milling conditions, i.e. the ball to powder ratio (BPR), ball sizes, and milling time, were varied to investigate their effect on ...
Guangjie Feng +8 more
doaj +1 more source